Dukane 8055 user manual Be careful in handling the light source lamp

Page 50

Safety Precautions (continued)

WARNING

Be careful in handling the light source lamp.

The projector uses a high-pressure mercury glass lamp made of glass. The lamp can break with a loud bang, or burn out. When the bulb bursts, it is possible for shards of glass to fly into the lamp housing, and for gas containing mercury to escape from the projector’s vent holes.

Please carefully read the section “Lamp”.

Be careful in handling the power cord and external connection cables. If you keep using a damaged the power cord or cables, it can cause a fire or electrical shock. Do not apply too much heat, pressure or tension to the power cord and cables.

If the power cord or cables is damaged (exposed or broken core wires, etc.), contact your dealer.

•Do not place the projector or heavy objects on the power cord and cables. Also, do not place a spread, cover, etc, over them because this could result in the inadvertent placing of heavy objects on the concealed power cord or cables.

•Do not pull the power cord and cables. When connecting and disconnecting the power cord or cables, do it with your hand holding the plug or connector.

•Do not place the cord near the heater.

•Avoid bending the power cord sharply.

•Do not attempt to work on the power cord.

Be careful in handling the battery of the remote control.

Incorrect handling of the battery could result in fire or personal injury. The battery may explode if not handled properly.

•Keep the battery away from children and pets. If swallowed consult a physician immediately for emergency treatment.

•Do not allow the battery in a fire or water.

•Avoid fire or high-temperature environment.

•Do not hold the battery with the metallic tweezers.

•Keep the battery in a dark, cool and dry play.

•Do not short circuit the battery.

•Do not recharge, disassemble or solder the battery.

•Do not give the battery a physical impact.

•Use only the battery specified in the other manual of this projector.

•Make sure the plus and minus terminals are correctly aligned when loading the battery.

•If you observe a leakage of the battery, wipe out the flower and then replace the battery. If the flower adheres your body or clothes, rinse well with water.

•Obey the local laws on disposing the battery.

4

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Model Page 8055 ProjectorContents Projector Features Fastening The Lens Cap Part NamesProjector Input button Power indicator Temp indicator ProjectorRemote Control Setting Up ArrangementAs necessary, you can also finely Adjusting The Projectors ElevatorAdjust the height of the projector by Twisting the elevator feet by handConnecting Your Devices Connecting to a computer AUDIO-L AUDIO-R G B RConnecting Power Supply Firmly plug the power cord’s plug Into the outletClose Battery cover Remote ControlRemove Battery cover Putting BatteriesOperating The Remote Control When the lens cap is attached, remove Power ON/OFFTurning On The Power Set the power switch to onSelecting An Input Signal Power switch OFF position Turning Off The PowerSwitch the power switch to O OFF Attached the lens capTemporarily Muting The Sound Adjusting The VolumeOperating Press the Position button Adjusting The PositionUse Buttons to adjust Position Using The Automatic Adjustment Feature Correcting Keystone DistortionsFreezing The Screen Using The Magnify FeatureUse Buttons to adjust the zoom Level Press the Magnify on buttonTemporarily Blanking The Screen Signal SearchingSelecting The Aspect Ratio Multifunctional Settings Using The Menu FunctionsMain Menu Picture 1 Menu Picture 1 Menu Load/Save a SettingReset the PICTURE-1 Menu Items LOAD4Position PhasePicture 2 Menu SizeVideo Input MenuColor Space Frame LockInformation Input MenuVideo NR S2-ASPECTSearch AdjustAuto Menu Message Screen MenuStart UP Lamp Time Option MenuScreen Type USB Mouse/Keyboard Control Available Functions Remote Control OperationOperating The PC Screen Lamp Replacing The Lamp Air Filter Caring For The Air FilterHold the release buttons of the air Replacing The Air FilterNew air filter. Tell the dealer your air Filter, while pulling down itCaring For The Inside Of The Projector Caring For The Cabinet And Remote ControlOther Care Caring For The LensTroubleshooting Related MessagesRelated Messages Regarding The Indicator Lamps Power Lamp TempRegarding The Indicator Lamps IndicatorPhenomena That May Easily Be Mistaken For Machine Defects Warranty And After-Service Phenomena That May Easily Be Mistaken For Machine DefectsSpecifications SpecificationAbout The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Technical Page Text Example Of Computer SignalResolution FH kHz FV Hz Rating Signal mode Display Initial Set Signals Connection To The Mouse Control Connecting The CableCommunications Setting RS-232C CommunicationUsing the projector default settings Reset Command Requesting projector status Get commandChanging the projector settings Set command Increasing the projector setting value Increment commandCommand Data Chart 4A D2日本語 Be EF FE D7 Be EF EC D9 Auto RGB Be EF FB D8 Mute Turn OFF Be EF Dukane Corporation Audio Visual Products

8055 specifications

The Dukane 8055 is an advanced ultrasonic welding machine designed to deliver exceptional performance for various manufacturing applications. Known for its precision and reliability, the Dukane 8055 is ideal for industries such as automotive, medical, and electronics, where high-quality joining processes are crucial.

One of the standout features of the Dukane 8055 is its robust ultrasonic technology. It employs high-frequency sound waves to create localized heating at the joint interface of thermoplastic materials. This method significantly reduces cycle times, improving productivity while ensuring consistent weld quality. The 8055 offers an adjustable frequency capability, allowing operators to optimize the welding process based on the specific materials being used.

The machine's user-friendly interface includes a touchscreen control panel, making it easy to set parameters and monitor the welding process in real time. This feature enhances operational efficiency by enabling quick adjustments to be made on the fly, ensuring that production runs smoothly.

Another significant characteristic of the Dukane 8055 is its integration with advanced software systems. The machine comes equipped with data logging capabilities, allowing users to track and analyze performance metrics. This data can be instrumental in identifying trends, ensuring compliance with industry standards, and implementing continuous improvement initiatives.

The Dukane 8055 also prioritizes safety and reliability. It is designed with various safety features, including automatic shutdown in case of abnormalities, ensuring minimal risk to operators and equipment. The robust construction of the machine ensures longevity even under demanding production environments.

Additionally, the Dukane 8055 is versatile, capable of accommodating various welding tools and accessories. This flexibility allows manufacturers to easily switch between different applications, from complex assembly tasks to simple joining processes, making it a valuable asset to any production line.

In summary, the Dukane 8055 ultrasonic welding machine stands out with its advanced technology, user-friendly controls, data logging features, and robust design. Its ability to adapt to various applications while ensuring high-quality results makes it an exemplary choice for manufacturers seeking efficiency and reliability in their joining processes. With the Dukane 8055, companies can enhance their production capabilities while maintaining the highest standards of quality.
Top Page Image Contents