Dukane 8055 user manual Regulatory Notices

Page 55

Regulatory Notices

FCC Statement Warning

WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

INSTRUCTIONS TO USERS: This equipment complies with the requirements of FCC (Federal Communication Commission) equipment provided that the following conditions are met. Some cables have to be used with the core set. Use the accessory cable or a designated-type cable for the connection. For cables that have a core only at one end, connect the core to the projector.

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

For the Customers in CANADA

NOTICE: This Class B digital apparatus complies with Canadian ICES-003.

Warranty And After-Service

Unless seen any abnormal operations (mentioned with the first paragraph of WARNING in this manual), when a problem occurs with the equipment, first refer to the “Troubleshooting” section of the “User’s manual – Operating Guide”, and run through the suggested checks.

If this does not resolve the problem contact your dealer or service company. They will tell you what warranty condition is applied.

9

Page 54 Page 56
Image 55
Page 54 Page 56
Contents Model Page Projector 8055Contents Projector Features Projector Part NamesFastening The Lens Cap Projector Input button Power indicator Temp indicatorRemote Control Arrangement Setting UpTwisting the elevator feet by hand Adjusting The Projectors ElevatorAdjust the height of the projector by As necessary, you can also finelyConnecting Your Devices AUDIO-L AUDIO-R G B R Connecting to a computerFirmly plug the power cord’s plug Into the outlet Connecting Power SupplyPutting Batteries Remote ControlRemove Battery cover Close Battery coverOperating The Remote Control Set the power switch to on Power ON/OFFTurning On The Power When the lens cap is attached, removeSelecting An Input Signal Attached the lens cap Turning Off The PowerSwitch the power switch to O OFF Power switch OFF positionOperating Adjusting The VolumeTemporarily Muting The Sound Use Buttons to adjust Position Adjusting The PositionPress the Position button Correcting Keystone Distortions Using The Automatic Adjustment FeaturePress the Magnify on button Using The Magnify FeatureUse Buttons to adjust the zoom Level Freezing The ScreenSelecting The Aspect Ratio Signal SearchingTemporarily Blanking The Screen Using The Menu Functions Multifunctional SettingsMain Menu Picture 1 Menu LOAD4 Load/Save a SettingReset the PICTURE-1 Menu Items Picture 1 MenuSize PhasePicture 2 Menu PositionFrame Lock Input MenuColor Space VideoS2-ASPECT Input MenuVideo NR InformationAuto Menu AdjustSearch Start UP Screen MenuMessage Screen Type Option MenuLamp Time Operating The PC Screen Available Functions Remote Control OperationUSB Mouse/Keyboard Control Lamp Replacing The Lamp Caring For The Air Filter Air FilterFilter, while pulling down it Replacing The Air FilterNew air filter. Tell the dealer your air Hold the release buttons of the airCaring For The Lens Caring For The Cabinet And Remote ControlOther Care Caring For The Inside Of The ProjectorRelated Messages TroubleshootingRelated Messages Power Lamp Temp Regarding The Indicator LampsIndicator Regarding The Indicator LampsPhenomena That May Easily Be Mistaken For Machine Defects Phenomena That May Easily Be Mistaken For Machine Defects Warranty And After-ServiceSpecification SpecificationsAbout The Symbols Safety Precautions Safety Precautions Be careful in handling the light source lamp Be careful in moving the projector Do not give the remote control any physical impact Take care not to fatigue your eyes Lamp Regulatory Notices Page Technical Page Resolution FH kHz FV Hz Rating Signal mode Display Example Of Computer SignalText Initial Set Signals RS-232C Communication Connecting The CableCommunications Setting Connection To The Mouse ControlIncreasing the projector setting value Increment command Requesting projector status Get commandChanging the projector settings Set command Using the projector default settings Reset Command4A D2 Command Data Chart日本語 Be EF FE D7 Be EF EC D9 Auto RGB Be EF FB D8 Mute Turn OFF Be EF Dukane Corporation Audio Visual Products

8055 specifications

The Dukane 8055 is an advanced ultrasonic welding machine designed to deliver exceptional performance for various manufacturing applications. Known for its precision and reliability, the Dukane 8055 is ideal for industries such as automotive, medical, and electronics, where high-quality joining processes are crucial.

One of the standout features of the Dukane 8055 is its robust ultrasonic technology. It employs high-frequency sound waves to create localized heating at the joint interface of thermoplastic materials. This method significantly reduces cycle times, improving productivity while ensuring consistent weld quality. The 8055 offers an adjustable frequency capability, allowing operators to optimize the welding process based on the specific materials being used.

The machine's user-friendly interface includes a touchscreen control panel, making it easy to set parameters and monitor the welding process in real time. This feature enhances operational efficiency by enabling quick adjustments to be made on the fly, ensuring that production runs smoothly.

Another significant characteristic of the Dukane 8055 is its integration with advanced software systems. The machine comes equipped with data logging capabilities, allowing users to track and analyze performance metrics. This data can be instrumental in identifying trends, ensuring compliance with industry standards, and implementing continuous improvement initiatives.

The Dukane 8055 also prioritizes safety and reliability. It is designed with various safety features, including automatic shutdown in case of abnormalities, ensuring minimal risk to operators and equipment. The robust construction of the machine ensures longevity even under demanding production environments.

Additionally, the Dukane 8055 is versatile, capable of accommodating various welding tools and accessories. This flexibility allows manufacturers to easily switch between different applications, from complex assembly tasks to simple joining processes, making it a valuable asset to any production line.

In summary, the Dukane 8055 ultrasonic welding machine stands out with its advanced technology, user-friendly controls, data logging features, and robust design. Its ability to adapt to various applications while ensuring high-quality results makes it an exemplary choice for manufacturers seeking efficiency and reliability in their joining processes. With the Dukane 8055, companies can enhance their production capabilities while maintaining the highest standards of quality.
Top Page Image Contents