Canon 7545 To change the code of Projector, To change the code of the Remote Control Unit

Page 36

SETTING

Power management

This function turns Projection Lamp off when this projector detects signal interruption and is not used for a certain period in order to reduce power consumption and maintain the Lamp-life. (This projector is shipped with this function ON.)

Power Management function operates to turn Projection Lamp off when the input signal is interrupted and any button is not pressed over 5 minutes. This function operates as follows;

1.When any input signal is interrupted, “No signal” and the counting down display appears (for 5 minutes).

2.After counting down for 5 minutes, projector lamp and READY indicator are turned off.

3.When READY indicator flashing, Projection Lamp can be turned on again (Power Management mode).

In this Power Management mode, Projection Lamp is automatically turned on when the input signal connected or projector is operated with any button on Top Control or on Remote Control Unit again.

Time left until Lamp off.

Press SET button at this icon to dis- play other items.

On start

When this function is “On,” projector is automatically turned on just by connecting AC Power cord to a wall outlet.

Note ; Be sure to turn projector off properly (refer to the section “TURNING OFF THE PROJECTOR” on P19). If projector is turned off in the wrong steps, On Start function does not operate properly.

Remote control

This projector has two different remote control codes; the factory-set normal code (Code 1) and the secondary code (Code 2). This switching function prevents remote control operation mixture (jam) when operating several projectors or video equipment together.

When operating projector in “Code 2,” both projector and Remote Control Unit must be switched to “Code 2.”

To change the code of Projector;

Set Remote control in the SETTING MENU to “Code 2.”

To change the code of the Remote Control Unit;

Press both MENU and IMAGE buttons on Remote Control Unit together for over 10 seconds.

After changing the code, make sure Remote Control operates properly.

To return to the normal code (Code 1), operate both projector and Remote Control in the ways above again.

NOTE : When batteries of Remote Control Unit are replaced or ALL- OFF switch is turned to “ALL-OFF,” the remote transmit code automatically returns to the normal code (Code 1).

Lamp counter reset

This function is used to reset Lamp Replace Counter. When replacing Projection Lamp, reset Lamp Replace Counter by using this function. Refer to page 39 for operation.

Press SET button at this icon to dis- play previous items.

Move the pointer to the item and then press POINT LEFT/RIGHT button(s).

Move the pointer to Lamp counter reset and then press SET button. The message “Lamp replace counter reset?” is displayed.

36

Image 36
Contents LV-7545 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Motor-driven Lens ShiftPreparation Name of Each Part of ProjectorSETTING-UP Projector Connecting AC Power CordFor Continental Europe Preparation Positioning Projector Room LightPreparation Adjustable Feet Moving ProjectorConnecting Projector USB Connector Series BTerminals of Projector Audio Input JacksConnecting to Computer Terminals ProjectorConnecting to Video Equipment Audio VideoOperation of Remote Control Before OperationLaser Pointer Function Volume Button Wired Remote JackZoom Button Focus ButtonTOP Controls and Indicators Ready IndicatorHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Guide WindowSound Menu Basic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Zoom AdjustmentLens Shift Adjustment Keystone AdjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System InputPC Adjustment Auto PC AdjustmentComputer Input Automatic MULTI-SCAN System Select Computer System ManuallyComputer Input Manual PC Adjustment PC Adjust MenuDisplay area Display area HFull screen Computer Input Compatible Computer Specifications Resolution640 x 31.469 59.940 1024 x 48.363 60.004Picture Image Adjustments Image Level Select DirectImage Level Select Menu Image Select MenuComputer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoComponent Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Setting MenuTo change the code of the Remote Control Unit To change the code of ProjectorSETTING/APPENDIX Operating Wireless MouseInstallation Operating Wireless MouseMaintenance AIR Filter Care and CleaningCleaning Projection Lens Appendix Lamp Replacement Lamp Replace CounterTroubleshooting Remote Control Unit Wireless MouseDoes not work Function does notTechnical Specifications Optional PartsAppendix Configurations of the Terminals USB Connector Series BCanon CANADA, INC