Canon 7545 owner manual Troubleshooting

Page 40

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check the matters below once again.

1.Make sure you have connected a projector to your computer or video equipment as described in the section "CONNECTING THE PROJECTOR" on pages 11 ~ 13.

2.Check cable connection. Verify that all computer, video and power cord are properly connected.

3.Verify that all power is switched on.

4.If a projector still does not produce an image, re-start your computer.

5.If an image still does not appear, unplug a projector from your computer and check your computer monitor's display. The problem may be with your graphics controller rather than with a projector. (When you reconnect a projector, be sure to turn the computer and monitor off before you power up the projector. Power the equipment back on in order of : Projector and computer.)

6.If the problem still exists, check following chart.

Problem:

Try these Solutions

No power.

Plug a projector into your AC outlet.

 

Make sure READY Indicator lights.

 

Wait 90 seconds after a projector is turned OFF when turning a projector back on.

 

NOTE : After pressing Power ON-OFF button to OFF, make sure a projector works as

 

follows:

 

1. LAMP indicator lights bright and READY indicator turns off.

 

2. After 90 seconds, READY indicator lights green again and a projector may be

 

turned on by pressing Power ON-OFF button.

 

Check WARNING TEMP. indicator. If this indicator flashes red, a projector cannot be

 

turned on.

 

(See "TURNING ON/OFF PROJECTOR" section on page 19.)

 

Check Projection Lamp. (Refer to page 39.)

 

 

Image is out of

Adjust focus of a projector.

focus.

Make sure a projection screen is at least 4.6’ (1.4m) from the projector.

Check Projection Lens to see if it needs cleaning.

 

 

NOTE : Moving a projector from a cool temperature location to a warm temperature location

 

may result in moisture condensation on Projection Lens. In such an event, leave a

 

projector OFF and wait until condensation disappears.

 

 

Picture is Left/Right

Check Ceiling / Rear feature. (See “SETTING” section on page 35.)

reversed.

 

 

 

Picture is

Check Ceiling feature. (See “SETTING” section on page 35.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

Check Display feature.(See “SETTING” section on page 35.)

not seen during the

 

Operation.

 

 

 

No image.

Check connection between your computer or video equipment and a projector.

 

Check NO SHOW function. (Refer to P21.)

 

When turning a projector on, it takes about 30 seconds to display an image.

 

Check the system that you select is corresponding with your computer or video

 

equipment.

 

Make sure the temperature is not out of the Operating Temperature (5°C ~ 35°C).

 

 

No sound.

Check audio cable connection from audio input source.

 

Adjust the audio source.

 

Press VOLUME (+) button.

 

Press MUTE button.

 

 

40

Image 40
Contents LV-7545 To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Features and Design Compact Design Motor-driven Lens ShiftPreparation Name of Each Part of ProjectorConnecting AC Power Cord SETTING-UP ProjectorFor Continental Europe Preparation Positioning Projector Room LightPreparation Adjustable Feet Moving ProjectorConnecting Projector USB Connector Series BTerminals of Projector Audio Input JacksConnecting to Computer Terminals ProjectorConnecting to Video Equipment Audio VideoBefore Operation Operation of Remote ControlLaser Pointer Function Volume Button Wired Remote JackZoom Button Focus ButtonTOP Controls and Indicators Ready IndicatorOperating ON-SCREEN Menu HOW to Operate ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Guide Window Before Operation Menu BARSound Menu Basic Operation Turning on / OFF ProjectorTurning on Projector Turning OFF ProjectorAdjusting Screen Zoom AdjustmentLens Shift Adjustment Keystone AdjustmentSound Adjustment Computer Input Selecting Input SourceSelecting Computer System InputPC Adjustment Auto PC AdjustmentComputer Input Automatic MULTI-SCAN System Select Computer System ManuallyComputer Input Manual PC Adjustment PC Adjust MenuDisplay area H Display areaFull screen Computer Input Compatible Computer Specifications Resolution640 x 31.469 59.940 1024 x 48.363 60.004Picture Image Adjustments Image Level Select DirectImage Level Select Menu Image Select MenuComputer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoComponent Video Signal Format Selecting Video SystemPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N AV System Menu Video or S-VIDEOCinema Video Input Image Level Adjustment Provides image at a normal video aspect ratio of 4 Setting Setting MenuTo change the code of the Remote Control Unit To change the code of ProjectorSETTING/APPENDIX Operating Wireless MouseInstallation Operating Wireless MouseAIR Filter Care and Cleaning MaintenanceCleaning Projection Lens Appendix Lamp Replacement Lamp Replace CounterTroubleshooting Remote Control Unit Wireless MouseDoes not work Function does notTechnical Specifications Optional PartsAppendix Configurations of the Terminals USB Connector Series BCanon CANADA, INC