Compaq 3000 manual Class a Equipment, Class B Equipment, 2Regulatory Compliance Notices

Page 125

B-2Regulatory Compliance Notices

Class A Equipment

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at personal expense.

Class B Equipment

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Consult the dealer or an experienced radio or television technician for help.

Image 125
Contents ProLiant Compaq ProLiant 3000 Setup and Installation Guide Contents Iv About This Guide Installation OverviewInstalling Hardware Options Vi About This Guide Integrated ManagementVii Appendix CViii About This Guide About This GuideHow this Manual is Organized Keys Text ConventionsProduct Safety Information Symbols in TextSymbols on Equipment About This GuideProLiant 3000 Setup and Installation Guide Compaq CDs Getting HelpCompaq Systems Reference Library CD Compaq SmartStart and Support Software CDCompaq Web Site Other Hardcopy DocumentsCompaq Management CD XiiiXiv About This Guide Telephone NumbersFinland 9800-206-720 90-6155-9899 Xvi About This Guide Processor Boards Compaq ProLiant 3000 Server FeaturesStandard Features Cache Memory and System Architecture 2Compaq ProLiant 3000 Server FeaturesSystem Memory Expansion SlotsVideo Media BaysKeyboard System Management High-Availability Features4Compaq ProLiant 3000 Server Features Fans Power SupplyWarranty SmartStart Management and Configuration Tools6Compaq ProLiant 3000 Server Features Compaq Insight Manager Disk Drive Fault Tolerance8Compaq ProLiant 3000 Server Features Security FeaturesAutomatic Server Recovery-2 ASR2 Compaq Integrated Management Display Compaq Integrated Remote Console10Compaq ProLiant 3000 Server Features Supported Drive ConfigurationsInterlock Switches Installation Overview 2Installation Overview Server Warnings and PrecautionsPower Requirements Pre-installation PlanningGrounding Server Temperature Requirements4Installation Overview Installing a Rack Mount Model Installation Procedure6Installation Overview Installing a Tower ModelProLiant 3000 Setup and Installation Guide Rack Warnings and Precautions Rack-Mount Server Installation2Rack-Mount Server Installation Rack Internal Temperature Maximums Rack Temperature RequirementsAirflow Requirements 4Rack-Mount Server InstallationLocating Materials and Documentation Unpacking the Server6Rack-Mount Server Installation ProLiant 3000 Setup and Installation Guide Preparing the Mounting Brackets Slide Rail Assemblies 8Rack-Mount Server InstallationAttaching the Bracket Rail to the Mounting Bracket Removing the component rail from the bracket rail 10Rack-Mount Server InstallationProLiant 3000 Setup and Installation Guide 12Rack-Mount Server Installation Attaching the bracket rail to the mounting bracket Measuring with the Template Attaching the Mounting Bracket Slide Assembly to the Rack14Rack-Mount Server Installation ProLiant 3000 Setup and Installation Guide Inserting Cage Nuts in the Rack Frame 16Rack-Mount Server InstallationInserting cage nuts Attaching the Mounting Bracket Assembly to the RackImportant Use only the bottom hole of the bracket as shown 18Rack-Mount Server Installation11.Cage nut and back of mounting bracket assembly installed Attaching Component Rails to the Server 20Rack-Mount Server Installation13.Attaching a cable management arm bracket to the server Attaching the Cable Management Arm BracketLoading the Rack Server 22Rack-Mount Server Installation14.Loading the rack server Attaching the Cable Management Arm 24Rack-Mount Server InstallationProLiant 3000 Setup and Installation Guide Attaching the Optional Cable Support 26Rack-Mount Server Installation17.Attaching the cable support to the rack Optional Installation ServiceInstalling Hardware Options 2Installing Hardware Options Accessing Non Hot-Plug AreasAccessing Processors, Memory Board, System Board ProLiant 3000 Setup and Installation Guide 4Installing Hardware Options Accessing the ProcessorRemoving the terminator board 6Installing Hardware Options Accessing Other System Board ComponentsAccessing Dimm Sockets on the Memory Board System Board SwitchesRemoving the memory board 8Installing Hardware OptionsMemory Banks Installing memory boardMemory banks on the system board J12 J11 J10 Bank 10Installing Hardware OptionsAccessing the Drive Cage Back Plane 10.Removing a fan 12Installing Hardware Options11.Removing the front panel 12.Partially pull out the drive cage 14Installing Hardware Options14.Removing the simplex enable board Installing the Duplex Enable Board Option15.Installing the duplex enable board 16Installing Hardware Options16.Re-installing the drive cage 17.Connectors on back of drive cage 18Installing Hardware Options18.Example cable connection to Scsi controller Replacing the Side Access PanelInterlock System 20Installing Hardware Options19.Removing the side panel Accessing Dimm Sockets on System Board20.Installing system board Dimm banks 22Installing Hardware OptionsAccessing the Hot-Plug Scsi Drives Accessing Hot-Plug Areas24Installing Hardware Options Scsi ID Numbers Or Channel B 26Installing Hardware OptionsInsight Manager Alert Pre-Failure WarrantyConfiguring the Server with SmartStart Server Configuration UtilitiesInserting the CD-ROM 2Server Configuration and UtilitiesUsing the System Configuration Utility Resolving Resource Conflicts 4Server Configuration and UtilitiesStarting the System Configuration Utility 6Server Configuration and Utilities System Configuration Utility Main MenuSystem Configuration Menu Add or Remove Boards Configuring HardwareSystem Partition 8Server Configuration and UtilitiesCreating a New System Partition Upgrading the System Partition 10Server Configuration and UtilitiesVerifying the System Partition Configuration Backup Configuration History Files Configuration Backup12Server Configuration and Utilities System Configuration History Log FilesRemoving Boards Configuring PCI Boards AutomaticallyInstalling an Operating System SMP Operating System Support 14Server Configuration and UtilitiesNovell NetWare Device Drivers form Compaq Manual installationLoading Compaq Device Drivers Microsoft Windows NT Device Drivers from Compaq 16Server Configuration and UtilitiesSCO OpenServer and SCO UnixWare Device Drivers from Compaq IBM OS/2 Device Drivers from Compaq 18Server Configuration and UtilitiesBanyan Vines Device Drivers from Compaq 20Server Configuration and Utilities Diagnostics and Other UtilitiesNormal Run-time Behavior Integrated ManagementIntegrated Management Display Idle Screen Text 2Integrated ManagementIntegrated Management Display buttons Navigation Buttons4Integrated Management Display SymbolsIntegrated Management Display Symbols Alert System Behavior with Error Events6Integrated Management Menu StructureIntegrated Management Log 8Integrated Management Multiple Ways of Viewing the LogCompaq Insight Manager Viewing the Event List 10Integrated Management Compaq Survey UtilityCompaq IML Management Utility END of Event List of Events12Integrated Management Event MessagesEvent Type Event Message Post Error General Requirements Power Cord Set RequirementsCountry-Specific Requirements Table A-1 Power Cord Set Requirements By Country2Power Cord Set Requirements Federal Communications Commission Notice Regulatory Compliance Notices2Regulatory Compliance Notices Class a EquipmentClass B Equipment Cables Modifications4Regulatory Compliance Notices Canadian NoticeAvis CanadienEuropean Union Notice Japanese Notice Australian Notice Laser Devices Laser Safety WarningsCompliance with Cdrh Regulations Compliance with International RegulationsLaser Information Laser Product Label8Regulatory Compliance Notices Battery Replacement NoticeInternal CD-ROM Internal CD-ROM DriveTable C-1 Index-1 IndexIndex Index-3 Scsi Index-5
Related manuals
Manual 103 pages 29.73 Kb