BOXLIGHT CP-320t manual Troubleshooting

Page 42

APPENDIX

TROUBLESHOOTING

Before calling your dealer or service center for assistance, check the items below once again.

●Make sure you have connected the projector to peripheral equipment as described properly in the section "CONNECTING PROJECTOR" on pages 11 ~ 13.

●Verify that all computer, video and power cord are properly connected and turn the equipment on.

●When you are operating the projector with a computer and it does not produce an image, restart the computer.

●Select the other input source.

Problem:

Try these Solutions

No power.

● Plug the projector into your AC outlet.

 

● Make sure the READY Indicator lights green.

 

● Wait 90 seconds after the projector is turned OFF when turning the projector back on.

 

NOTE : After pressing the Power ON-OFF button to OFF, make sure the projector works as

 

follows:

 

1. The LAMP indicator lights bright, and the READY indicator is turned off.

 

2. After 90 seconds, the READY indicator lights green again and the projector can

 

be turned on by pressing the Power ON-OFF button.

 

● Check the WARNING TEMP. indicator. If the indicator flashes red, the projector cannot

 

be turned on.

 

(Refer to the section "MAINTENANCE" on page 41.)

 

● Check the Projection Lamp. (Refer to page 37.)

 

 

Image is out of

● Adjust focus of the projector.

focus.

● Make sure the projection screen is at least 3.6’ (1.1m) from the projector.

● Check the Projection Lens to see if it needs cleaning.

 

 

NOTE : Moving the projector from a cool temperature location to a warm temperature

 

location may result in moisture condensation on the Projection Lens. In such an

 

event, leave the projector OFF and wait until condensation disappears.

 

 

Picture is Left/Right

● Check Ceiling / Rear feature. (See the “SETTING” section on page 36.)

reversed.

 

 

 

Picture is

● Check Ceiling feature. (See the “SETTING” section on page 36.)

Top/Bottom

 

reversed.

 

 

 

Some displays are

● Check Display feature.(See the “SETTING” section on page 36.)

not seen during the

 

Operation.

 

 

 

No image.

● Check the connection between your computer or video equipment and the projector.

 

● When turning the projector on, it takes about 30 seconds to display an image.

 

● Check the system that you select is corresponding with your computer or video

 

equipment.

 

● Make sure the temperature is not out of Operating Temperature (5°C ~ 35°C).

No sound.

● Check audio cable connection from audio input source.

 

● Adjust the audio source.

 

● Press the VOLUME (+) button.

 

● Press the MUTE button.

Computer 2 cannot

● Check the COMPUTER IN 2 / MONITOR OUT terminal is set as Computer 2. (See the

be selected.

“SETTING” section on page 36.)

 

 

 

42

Page 41 Page 43
Image 42
Page 41 Page 43
Contents Boxlight CP-320t To the Owner Safety Instructions Voor de klanten in NederlandCompliances Federal Communication Commission NoticeTable of Contents Color Systems Features and DesignComputers Component VideoPreparation Name of Each Part of ProjectorFor Continental Europe SETTING-UP ProjectorConnecting AC Power Cord For the U.S.A. and CanadaAdjustable Feet Preparation Positioning ProjectorRoom Light Preparation Installing Projector in Proper Position Moving ProjectorVideo Input Jack Audio Input Jacks Connecting ProjectorTerminals of Projector Computer Input DIGITAL/ANALOGConnecting to Computer Terminals ProjectorConnecting to Video Equipment TerminalsBefore Operation Operation of Remote ControlDIP Switch in the Battery Compartment Laser Pointer FunctionRemote Control Batteries Installation TOP Controls and Indicators Lamp Replace IndicatorHOW to Operate ON-SCREEN Menu Operating ON-SCREEN MenuFlow of ON-SCREEN Menu Operation Before Operation Menu BAR Guide WindowTurning on / OFF Projector Lamp modeBasic Operation Turning on ProjectorKeystone Adjustment Adjusting ScreenFocus Adjustment Picture Freeze FunctionBasic Operation No Show Function Sound AdjustmentTimer Function Direct OperationRGB Scart RGB Digital RGB Analog Selecting Input SourceRGB Input MenuSelect Computer System Manually Selecting Computer SystemComputer Input SvgaFreq Computer Input Compatible Computer SpecificationsResolution KHzPC Adjust Menu PC AdjustmentAuto PC Adjustment Auto PC AdjComputer Input Manual PC Adjustment Display area Display area HFull screen Image Level Select Menu Picture Image AdjustmentsImage Level Select Direct Image 1~4Computer Input Image Level Adjustment Image Adjust MenuPicture Screen Adjustment Screen MenuVideo Input VideoPAL / Secam / Ntsc / NTSC4.43 / PAL-M / PAL-N Component Video Signal FormatSelecting Video System AV System Menu Video or S-VIDEOCinema Image button Standard CinemaVideo Input Image Level Adjustment Reset all adjustment to their previous figure Setting Setting MenuSetting Menu To change the code of the Remote Control To change the code of the ProjectorAppendix Lamp ReplacementReset the Lamp Replace Counter Lamp ReplaceLamp Handling Precautions Appendix Lamp Replace CounterOperating Wireless Mouse InstallationOperating Wireless Mouse Cleaning Projection Lens MaintenanceAIR Filter Care and Cleaning TOP ControlTroubleshooting Not work Remote Control doesWireless Mouse Function does notIndicators Projector Condition Appendix Indicators and Projector ConditionTechnical Specifications Computer INPUT/MONITOR Output Terminal Analog Appendix Configurations of TerminalsTerminal HDB15-PIN Pin Configuration DVI-I Terminal DIGITAL/ANALOGOptional Parts Limited Warranty

CP-320t specifications

The BOXLIGHT CP-320t is a versatile and powerful interactive projector designed to enhance the learning and collaboration experience in various educational settings. Engineered with advanced technology, this projector aims to transform traditional teaching methods through captivating and engaging presentations.

One of the standout features of the CP-320t is its impressive brightness, boasting up to 3,200 ANSI lumens. This high level of brightness ensures vivid and clear images, making it ideal for use in well-lit classrooms or meeting rooms. The projector supports a native resolution of XGA (1024 x 768), delivering sharp details and vibrant colors that help facilitate effective communication.

The CP-320t incorporates an interactive capability that allows users to directly engage with projected content. The dual pen feature supports multiple users simultaneously, making it perfect for group activities and collaborative projects. This interactivity encourages student participation and fosters a more dynamic learning environment. Additionally, the projector offers touchscreen functionality, enabling gestures like tapping and swiping, reminiscent of using a tablet.

In terms of connectivity, the BOXLIGHT CP-320t excels with multiple inputs, including HDMI, VGA, and USB. This versatility allows for easy connectivity with various devices, such as laptops, tablets, and document cameras. The projector also features integrated speakers, providing clear audio to support multimedia presentations without the need for external sound systems.

Another notable characteristic of the CP-320t is its portability. Weighing only a few pounds, it can easily be transported between classrooms or offices. It also includes a long lamp life of up to 10,000 hours in eco mode, which significantly reduces maintenance costs and downtime, making it a cost-effective choice for schools and businesses.

The projector is equipped with the latest technologies to enhance image quality, including high contrast ratios and advanced color management systems, ensuring that visuals are both striking and accurate. The simple user interface allows for seamless navigation, making it easy for educators and presenters to adapt to different presentation needs without technical difficulties.

In summary, the BOXLIGHT CP-320t interactive projector combines brightness, interactivity, and connectivity in a portable, user-friendly package. Designed for modern educational environments, it provides an engaging platform that encourages participation and collaboration, making it an excellent choice for enhancing the teaching and learning experience.
Top Page Image Contents