BenQ MP623, MP624 user manual Connecting a Component Video source device

Page 21

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video output sockets available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to a Component Video source device:

1.Take a Component Video to VGA (D-Sub) adaptor cable and connect the end with 3 RCA type connectors to the Component Video output sockets of the Video source device. Match the color of the plugs to the color of the sockets; green to green, blue to blue, and red to red.

2.Connect the other end of the Component Video to VGA (D-Sub) adaptor cable (with a D-Sub type connector) to the D-SUB/COMP. IN socket on the projector.

3.If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the AUDIO socket of the projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Adjusting the sound" on page 39 for details.

The final connection path should be like that shown in the following diagram:

Component Video to VGA	Audio
(D-Sub) adaptor cable	cable
AV device

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 19 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

Connection 21

Image 21

Contents MP623/MP624 Digital Projector WelcomeTable of contents Refer servicing to qualified service personnel Important safety instructionsFuture reference Projector lamp is on Do not look straight at the projectorSafety Instructions Do not block the ventilation holes This Apparatus Must be Earthed Ceiling mounting the projectorProjector features IntroductionIntroduction Shipping contents Projector exterior view Front/upper sideRear/lower side Projector Controls and functionsRemote control Replacing the remote control battery Remote control effective rangePull out the battery holder Operating the projector from the rearChoosing a location Positioning your projectorObtaining a preferred projected image size Page Projection dimensions Connecting a computer Connecting a computer or monitorConnection To connect the projector to a notebook or desktop computer To connect the projector to a monitor Connecting a monitorConnecting audio Connecting Video source devicesBest video quality Better video qualityTo connect the projector to an Hdmi device Connecting an Hdmi deviceTo connect the projector to a Component Video source device Connecting a Component Video source deviceTo connect the projector to an S-Video source device Connecting an S-Video source deviceTo connect the projector to a composite Video source device Connecting a composite Video source deviceOperation Heard. The Power indicator light flashesStarting up the projector OperationUse / to highlight the System Setup Basic menu Using the menusSetting a password Utilizing the password functionIf you forget the password Security SettingsChanging the password Entering the password recall procedureDisabling the password function Enter a new passwordChanging color space Switching input signalAdjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting keystone Magnifying and searching for detailsAbout the aspect ratio Selecting the aspect ratioPicture modes for different types of signals Selecting a picture modePC input signals D-Sub / Comp. analog RGB Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorSetting the User 1/User 2 mode Adjusting BrightnessAdjusting Tint Adjusting ColorAdjusting Sharpness Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Top-Left Bottom-Left Top- Right Bottom-Right Setting the presentation timerTo cancel the timer, perform the following steps How to use the Timer On key?Hiding the image Or go to the System Setup Basic Panel Utilizing FAQ functionLocking control keys Freezing the imageAdjusting the sound level Adjusting the soundTurning off the Power on/off ring tone Operating in a high altitude environmentShutting down the projector Personalizing the projector menu displayMenu operation Menu systemMain menu Sub-menu Options Language BasicAdvanced Description of each menu Save Settings TemperatureTimer Auto Power OffSleep Timer System Setup Basic menu System Setup Advanced menuAudio Settings Menu SettingsSettings Lamp SettingsReset All SecurityFAQ-Features Service FAQ-Image InstallationInformation menu CurrentCare of the projector MaintenanceSetting Auto Power Off Setting Lamp mode as EconomicLamp information Getting to know the lamp hourTiming of replacing the lamp Turn the power off and disconnect Loosen the screw that secures the lamp MaintenanceReplacing the lamp Tighten the screw that secures the lamp Setup Advanced Lamp Settings menu Resetting the lamp timerDisplays. Press to highlight Reset lamp Restart the projectorIndicators OrangeOff Red Troubleshooting Projector specifications SpecificationsDimensions Timing chartSupported timing for PC input Supported timing for Hdmi Hdcp input Resolution ModeSupported timing for Video and S-Video inputs HorizontalSupported timing for Component YPbPr input Signal Format Horizontal Frequency kHz Vertical Frequency HzLimited warranty Warranty and Copyright informationCopyright DisclaimerFCC statement Regulation statementsEEC statement Weee directive