BenQ MP624, MP623 user manual Connecting an S-Video source device

Page 22

Connecting an S-Video source device

Examine your Video source device to determine if it has an unused S-Video output socket available:

•If so, you can continue with this procedure.

•If not, you will need to reassess which method you can use to connect to the device.

To connect the projector to an S-Video source device:

1.Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.

2.Connect the other end of the S-Video cable to the S-VIDEOsocket on the projector.

3.If you wish to make use of the projector (mixed mono) speaker in your presentations, take a suitable audio cable and connect one end of the cable to the audio output socket of the device, and the other end to the AUDIO socket of the projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD) menus. See "Adjusting the sound" on page 39 for details.

The final connection path should be like that shown in the following diagram:

Audio cable

S-Video cable

AV device

• The projector is only capable of playing mixed mono audio, even if a stereo audio input is connected. See "Connecting audio" on page 19 for details.

•If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly.

•If you have already made a Component Video connection between the projector and this S-Video source device using Component Video connections, you need not connect to this device using an S-Video connection as this makes an unnecessary second connection of poorer picture quality. See "Connecting Video source devices" on page 19 for details.

22 Connection

Image 22

Contents Welcome MP623/MP624 Digital ProjectorTable of contents Future reference Projector lamp is on Important safety instructionsRefer servicing to qualified service personnel Do not look straight at the projectorSafety Instructions Do not block the ventilation holes Ceiling mounting the projector This Apparatus Must be EarthedIntroduction Projector featuresIntroduction Shipping contents Front/upper side Projector exterior viewRear/lower side Controls and functions ProjectorRemote control Pull out the battery holder Remote control effective rangeReplacing the remote control battery Operating the projector from the rearPositioning your projector Choosing a locationObtaining a preferred projected image size Page Projection dimensions Connection Connecting a computer or monitorConnecting a computer To connect the projector to a notebook or desktop computerConnecting a monitor To connect the projector to a monitor Best video quality Connecting Video source devices Connecting audio Better video qualityConnecting an Hdmi device To connect the projector to an Hdmi deviceConnecting a Component Video source device To connect the projector to a Component Video source deviceConnecting an S-Video source device To connect the projector to an S-Video source deviceConnecting a composite Video source device To connect the projector to a composite Video source deviceStarting up the projector Heard. The Power indicator light flashesOperation OperationUsing the menus Use / to highlight the System Setup Basic menuIf you forget the password Utilizing the password functionSetting a password Security SettingsDisabling the password function Entering the password recall procedureChanging the password Enter a new passwordSwitching input signal Changing color spaceAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityMagnifying and searching for details Correcting keystoneSelecting the aspect ratio About the aspect ratioPC input signals D-Sub / Comp. analog RGB Selecting a picture modePicture modes for different types of signals Optimizing the imageSetting the User 1/User 2 mode Using Wall ColorFine-tuning the image quality in user modes Adjusting BrightnessAdjusting Sharpness Adjusting ColorAdjusting Tint Adjusting Brilliant ColorPress Mode/Enter and the 3D Color Management page displays Setting the presentation timer Top-Left Bottom-Left Top- Right Bottom-RightHow to use the Timer On key? To cancel the timer, perform the following stepsHiding the image Locking control keys Utilizing FAQ functionOr go to the System Setup Basic Panel Freezing the imageTurning off the Power on/off ring tone Adjusting the soundAdjusting the sound level Operating in a high altitude environmentPersonalizing the projector menu display Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Basic LanguageAdvanced Description of each menu Timer TemperatureSave Settings Auto Power OffAudio Settings System Setup Basic menu System Setup Advanced menuSleep Timer Menu SettingsReset All Lamp SettingsSettings SecurityInformation menu FAQ-Image InstallationFAQ-Features Service CurrentMaintenance Care of the projectorLamp information Setting Lamp mode as EconomicSetting Auto Power Off Getting to know the lamp hourTiming of replacing the lamp Loosen the screw that secures the lamp Maintenance Turn the power off and disconnectReplacing the lamp Tighten the screw that secures the lamp Displays. Press to highlight Reset lamp Resetting the lamp timerSetup Advanced Lamp Settings menu Restart the projectorOrange IndicatorsOff Red Troubleshooting Specifications Projector specificationsTiming chart DimensionsSupported timing for PC input Supported timing for Video and S-Video inputs Resolution ModeSupported timing for Hdmi Hdcp input HorizontalSignal Format Horizontal Frequency kHz Vertical Frequency Hz Supported timing for Component YPbPr inputCopyright Warranty and Copyright informationLimited warranty DisclaimerEEC statement Regulation statementsFCC statement Weee directive