BenQ MP525 ST Color Tint, Sharpness, Brilliant Color, Temperature, 3D Color, Management, Search

Page 47

Function

(default setting/value)

Color

(0)

Tint

2.

(0)

 

PICTURE

Sharpness

 

menu

(15)

Brilliant Color

 

 

(On)

 

Color

 

Temperature

 

3D Color

 

Management

 

Save Settings

3.

Quick Auto

SOURCE

Search

Color Space

 

(On)

 

menu

Conversion

(depends on the

 

selected input signal)

4.

Presentation

SYSTEMSETUP: Basicmenu

Timer

 

(Off)

 

 

 

 

Language

 

(

 

)

 

 

Description

Adjusts the color saturation level -- the amount of each color in a video image. See "Adjusting Color" on page 35 for details.

This function is only available when a Video or S-Video signal is selected and the system format is NTSC or PAL.

Adjusts the red and green color tones of the image. See "Adjusting Tint" on page 35 for details.

This function is only available when a Video or S-Video signal is selected and the system format is NTSC.

Adjusts the image to make it look sharper or softer. See "Adjusting Sharpness" on page 35 for details.

This function is only available when a Video or S-Video signal is selected and the system format is NTSC or PAL.

See "Adjusting Brilliant Color" on page 35 for details.

There are four color temperature settings available. See "Selecting a color temperature" on page 35 for details.

See "3D Color Management" on page 35 for details.

Saves the settings made for User 1 or User 2 mode.

See "Switching input signal" on page 30 for details.

See "Changing Color Space (MP515 ST only)" on page 30 for details.

Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 37 for details.

Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 26 for details.

Operation 47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents
Welcome Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Installation Introduction Projector featuresShipping contents Projector exterior view Projector Controls and functionsActivates the selected On-Screen Display OSD menu item Selects an available picture setupMode/Enter ModeDigital Zoom + Remote controlVolume + FreezeTimer Set up Remote control effective rangeReplacing the remote control battery Timer On Up/DownFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Positioning your projector Inch Projection dimensionsHdmi cable ConnectionVGA cable Video cable To connect the projector to a notebook or desktop computer Connecting a computer or monitorConnecting a computer Connecting a monitor MP525 ST onlyConnecting audio Connecting Video source devicesTo connect the projector to a Component Video source device Connecting a Component Video source deviceConnecting an Hdmi device MP515 ST only To connect the projector to an Hdmi deviceTo connect the projector to an S-Video/Video source device Connecting an S-Video/composite Video source deviceStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUsing the remote control Using the OSD menuPreferred language Using the menusUse / to highlight the System Setup Basic menu Press / to select aTo the Security Settings Using a security cable lockUtilizing the password function Setting a passwordChanging the password If you forget the passwordEntering the password recall procedure Disabling the password function Changing Color Space MP515 ST only Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Using Wall ColorSelecting a picture mode Adjusting Brightness Fine-tuning the image quality in user modesSetting the User 1/User 2 mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Adjusting ColorAdjusting Tint Adjusting SharpnessTo adjust the settings To highlight Off and press Mode/Enter Setting the presentation timerTo cancel the timer, perform the following steps Hiding the image How to use the Timer On key?Freezing the image Utilizing FAQ functionLocking control keys To activate the High Altitude ModeOperating in a high altitude environment Personalizing the projector menu display Adjusting the soundAdjusting the sound level Turning off the Power On/Off Ring ToneShutting down the projector Once the cooling process finishes, a Power Off Ring Basic Main menu Sub-menu OptionsAdvanced Informa Description of each menu Color Tint TemperatureSave Settings TimerSleep Timer Menu SettingsAuto Power Off Blank TimerSecurity Audio Settings Standby Monitor OutLamp Settings SettingsFAQ-Features Reset AllFAQ-Image InstallationCare of the projector MaintenanceExtending lamp life Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Maintenance Resetting the lamp timer Thermal events IndicatorsLight Status & Description Power events Lamp eventsCause Remedy TroubleshootingSpecifications Mm W x 114 mm H x 236 mm D DimensionsCeiling mount installation Supported timing for PC input-MP515 ST/MP525 ST Timing chartSupported timing for Hdmi Hdcp input-MP515 ST Supported timing for Component-YPbPrinput-MP515 ST/ MP525 ST Disclaimer Warranty and Copyright informationLimited warranty CopyrightWeee directive Regulation statementsFCC statement EEC statementRegulation statements
Related manuals
Manual 66 pages 478 b
Top Page Image Contents