BenQ W6000 Adjusting the projected image, Adjusting the projection angle, Two parallel sides

Page 25

Adjusting the projected image

Adjusting the projection angle

There are four adjuster feet on the bottom of the projector. These can be used if necessary to change the projection angle. Screw the feet in or out as appropriate to aim and level the projection angle.

If the screen and the projector are not perpendicular to each other, the projected image becomes vertical trapezoidal. To correct this problem, see "Correcting picture distortion" on page 25 for details.

Correcting picture distortion

Keystoning occurs when the projector is not perpendicular to the screen and is where the projected picture displays visible as a trapezoid shape like either of the following:

•Two parallel sides (left and right, or top and bottom) but is noticeably wider on either side.

•No parallel sides.

To correct the picture’s shape, you can perform the following steps.

1.Adjust the projection angle. Move the projector to be in front of the center of the screen with the center of the lens level with the screen.

2.If the picture is stilled distorted, or the projector is unable to be positioned as described above, you will need to manually correct the picture.

•Using the remote control or projector

i. Press one of the Arrow/Keystone keys on the remote control or projector (Left / , Up / , Right / , Down / ) to display the Keystone page.

ii. See step iv below for further operation.

English

•Using the OSD menu

i.Press MENU and then press / until the Display menu is highlighted.

ii.Press to highlight Keystone and press ENTER. The Keystone page displays.

iii.Highlight 2D Keystone and press ENTER. The keystone correction page displays.

iv.Press the key whose keystone icon is opposite to the shape of the projected picture. Continue pressing the same key or press the other keys until you are satisfied with the shape.

The values on the lower portion of the page change while pressing. When the values reach their maximum or minimum with repeated key presses, the picture’s shape will stop changing. You will not be able to change the picture further in that direction.

Two parallel sides

 

Press

Press

/ .

/ .

No parallel sides

 

Press

Press

/ .

/ .

Display

Aspect Ratio

Anamorphic

Keystone

ENTER

Position

 

Overscan Adjustment

0

PIP

 

PC & Component YPbPr Tuning

 

S-Video

EXIT Back

Keystone

 

2D Keystone

ENTER

 

EXIT Back

Keystone

1 0

EXIT Back

Using the projector

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents W6000 Digital Projector Home Cinema Series WelcomeTable of contents Important safety instructions Do not cover the projector with any item Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesCeiling mounting the projector Projector features Front and upper side view Projector exterior viewRear view Under viewControl panel Picture window control keys PIP, Size Remote controlTest InfoFloor Front Choosing a locationCeiling Front Floor RearDetermine the aspect ratio of your screen, 169 or 43? Obtaining a preferred projected image sizeInstallation for a 169 ratio screen Projection dimensionsHighest Installation for a 43 ratio screenLens Height HTo use the lens shift lever Shifting the projection lensPreparations Connecting Hdmi devicesReference Picture quality ComponentConnecting S-Video or video devices Connecting component-video devicesConnect the projector to a computer with a VGA cable Connecting a computerPreparations Turning the projector onUsing the OSD menu Fine-tuning the image size and clarityAdjust the projected picture to the size that You need using the zoom ring RingUsing a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projectorSetting a password Utilizing the password functionIf you forget the password To leave the OSD menu, press MenuChanging the password Entering the password recall procedureDisabling the password function Write down the number and turn off your projectorAdjusting the projection angle Adjusting the projected imageCorrecting picture distortion Two parallel sidesSelecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture modeResetting the picture mode Setting the User 1/User 2/User 3 modePress to highlight Load Settings From To reset the picture mode to the preset factory valuesFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperatureTo adjust and store the settings Setting Film ModeColor Management Selecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 displayOperating in a high altitude environment To activate High Altitude ModeDisplaying more than one image source simultaneously To display the PIP window Using the remote controlHighlight PIP and press / to select On PIP function is effective at below source combinationsLocking control keys Personalizing the projector menu displayTurning the projector off To lock the keysOn-Screen Display OSD structure On-Screen Display OSD menusMain menu Sub-menu Options Setup System SetupInformation Resolution Picture -- Advanced menu Picture -- Basic menuFunction Description Display menu System Setup menuAdvanced Setup menu Menu SettingsLamp Power Normal Reset Lamp TimerInformation menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projectorSetting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message Remove the lamp cover Resetting the lamp timer Power Temp Lamp Status & Description IndicatorsPower Lamp Status & DescriptionProblem Cause Remedy TroubleshootingOptical SpecificationsElectrical TerminalsCeiling mount installation DimensionsMm x 317 mm x 145 mm W x D x H Format Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHzFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputsCopyright WarrantyDisclaimer EEC statement for European users FCC statement for United States usersMIC statement Weee directiveEnglish
Related manuals
Manual 6 pages 48.59 Kb

W6000 specifications

The BenQ W6000 is a high-performance home theater projector that is designed to deliver an immersive viewing experience for movies, sports, and gaming. With its advanced features and cutting-edge technologies, the W6000 stands out in the crowded projector market, making it a popular choice for home cinephiles and casual viewers alike.

One of the key features of the BenQ W6000 is its impressive brightness, rated at 2000 ANSI lumens. This ensures that images remain vivid and clear even in rooms with ambient light. The projector's contrast ratio, reaching 3,000:1, enhances the depth of blacks and the brilliance of whites, providing an engaging viewing experience with rich detail.

The W6000 boasts Full HD 1080p resolution (1920 x 1080), which allows it to deliver crystal-clear images without any loss of detail. This is especially important for high-definition content, as it captures the intricacies of films and TV shows, making every scene come to life. Additionally, the projector is equipped with the latest DLP (Digital Light Processing) technology, ensuring smooth performance and vibrant color reproduction.

Color accuracy is a significant consideration for home theater projectors, and the BenQ W6000 excels in this area. With its 6-segment color wheel and BrilliantColor technology, it offers a wide color gamut that produces lifelike images with stunning realism. The projector also features a built-in color management system, allowing users to fine-tune color settings to their liking.

Another notable characteristic of the W6000 is its versatile lens design. The projector includes a 1.5x optical zoom and horizontal/vertical lens shift, providing flexible installation options. This feature is particularly beneficial when accommodating various room sizes and viewing distances, ensuring that users can enjoy a big-screen experience without compromising image quality.

Connectivity is also a strong point for the BenQ W6000, as it supports multiple inputs such as HDMI, VGA, and composite video. This allows users to connect a variety of devices, from laptops and gaming consoles to Blu-ray players and streaming devices. The projector is compatible with 3D content as well, making it an excellent choice for fans of immersive entertainment.

In summary, the BenQ W6000 is a feature-rich home theater projector that combines brightness, resolution, color accuracy, and flexibility. Its advanced DLP technology, high contrast ratio, and comprehensive connectivity options make it an ideal choice for anyone looking to elevate their home viewing experience. Whether you're watching the latest blockbuster or gaming with friends, the W6000 delivers outstanding performance and quality that is sure to impress.
Top Page Image Contents