BenQ MX520 user manual Adjusting the projected image, Adjusting the projection angle

Page 19

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with 1 quick-release adjuster foot and 1 rear adjuster foot. These adjusters change the image height and projection angle. To adjust the projector:

1.Press the quick-release button and lift the front of the projector. Once the image is positioned where you want it, release the quick-release button to lock the foot in position.

2.Screw the rear adjuster foot to fine-tune the

horizontal angle.

To retract the foot, hold up the projector while pressing the quick-release button, then slowly lower the projector. Screw the rear adjuster foot in a reverse direction.

If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Switching input signal" on page 24 for details.

2

1

Do not look into the lens while the lamp is on. The strong light from the lamp may cause damage to your eyes.

Be careful when you press the quick- release button as it is close to the exhaust vent where hot air comes from.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality. To do this, press AUTO on the projector or remote control. Within 3 seconds, the built-in Intelligent Auto Adjustment function will re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the corner of the screen for 3 seconds.

This function is only available when PC signal (analog RGB) is selected.

Fine-tuning the image size and clarity

1.

Adjust the projected image to the

2.

Sharpen the image by rotating the

size that you need using the zoom

focus ring.

ring.

Operation 19

Image 19

Contents MX520/MX703 Digital Projector Table of contents Safety Instructions Important safety instructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Introduction Projector featuresShipping contents Front/upper side Rear/lower side Projector exterior viewControls and functions Remote control Replacing the remote control batteries Remote control effective rangeFront Ceiling Positioning your projectorChoosing a location Front TableObtaining a preferred projected image size Projection dimensionsMX520 Screen size Projection distance mm Diagonal Min MX703Connection ConnectionBest Connecting video source devicesConnecting audio Terminal name Terminal appearanceStarting up the projector OperationFine-tuning the image size and clarity Adjusting the projected imageAdjusting the projection angle Auto-adjusting the imageCorrecting keystone Below is the overview of the OSD menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordChanging the password Entering the password recall procedureDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Go to the Picture Picture Mode menu Using Wall ColorSelecting a picture mode Setting the User 1/User 2 modeAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a color temperature 3D Color Management Setting a preferred color temperatureResetting current or all picture modes Setting the presentation timerSelection Description Top-Left Bottom-Left Top-Right Bottom-Right To cancel the timer, perform the following stepsRemote paging operations Freezing the imageOperating in a high altitude environment To activate the High Altitude ModeHiding the image Locking control keysTurning off the Power On/Off Ring Tone Adjusting the soundUsing the test pattern Adjusting the sound levelTo select Blackboard or Whiteboard Using the teaching templatesShutting down the projector Direct power offMenu system Menu operationMain menu Sub-menu Options Right/Bottom-Left Menu Settings Menu PositionBasic Menu Display Sec/10 sec/20 sec/30 sec/Always TimeColor System Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour IP AddressDescription of each menu Fine Tuning 3D Color Picture ModeTemperature Color TemperatureSearch TimerInstallation SettingsReceiver for System Setup Basic menu Function DescriptionOperation RemoteScreen LockBackground Color SplashBaud Rate System Setup Advanced menu Function DescriptionSettings for Reset AllSystem CurrentStatus Care of the projector MaintenanceGetting to know the lamp hour Lamp informationExtending lamp life Status Message Timing of replacing the lampReplacing the lamp Use the handle to slowly pull the lamp out Projector Resetting the lamp timerMaintenance Thermal events IndicatorsLight Status & Description Power events Lamp eventsTroubleshooting Projector specifications SpecificationsCeiling mount installation DimensionsSupported timing for PC input Timing chartKHz Supported timing for Hdmi Hdcp inputSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputTiming Disclaimer Warranty and Copyright informationLimited warranty Copyright