BenQ MX520 Main menu Sub-menu Options System Setup Advanced, Equivalent Lamp Hour, IP Address

Page 38

Main menu Sub-menu

Options

5. SYSTEM SETUP: Advanced

	High Altitude Mode		On/Off
		Mute	On/Off
	Audio Settings	Volume
	Audio Settings	Power On/Off	On/Off
		Power On/Off
		Ring Tone
		Ring Tone
		Lamp Mode	Normal/Economic/SmartEco
	Lamp Settings	Reset Lamp Timer
		Equivalent Lamp Hour
	Security	Change Password
	Security	Change Security
	Settings	Change Security	Power On Lock
		Settings
	Baud Rate		2400/4800/9600/14400/19200/
	Baud Rate		38400/57600/115200
			38400/57600/115200

	Test Pattern		On/Off
		Closed Caption	On/Off
	Closed Caption	Enable	On/Off
	Closed Caption	Enable
		Caption Version	CC1/CC2/CC3/CC4
		Network (for	On/Off
		MX703)	On/Off
	Standby	MX703)
	Standby	Monitor Out	On/Off
	Settings	Monitor Out	On/Off
	Settings	Audio Pass	Off/Computer 1/Computer 2/
		Audio Pass	Off/Computer 1/Computer 2/
		Through	Video,S-Video/HDMI
			Status
			DHCP
			IP Address
	Network	Wired LAN	Subnet Mask
	Network		Default Gateway
	Settings (for		Default Gateway

MX703)		DNS Server
MX703)		Apply
		Apply
	AMX Device	On/Off
	Discovery	On/Off
	Discovery
	MAC Address

	Reset All Settings
		•	Source
6.		•	Picture Mode
6.		•	Resolution
INFORMA Current System Status		•	3D Format
TION		•	Color System
		•	Equivalent Lamp Hour
		•	Firmware Version

Note that the menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.

38 Operation

Image 38

Contents MX520/MX703 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingMX520 Projection dimensionsObtaining a preferred projected image size MX703 Screen size Projection distance mm Diagonal MinConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuSelecting a color temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or Whiteboard Direct power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Menu Display Sec/10 sec/20 sec/30 sec/Always Time Menu Settings Menu PositionBasic Right/Bottom-LeftIP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color SystemDescription of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation Receiver forColor Splash LockBackground ScreenReset All System Setup Advanced menu Function DescriptionSettings for Baud RateStatus CurrentSystem Maintenance Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status MessageReplacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out ProjectorMaintenance Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzTiming Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer