BenQ MX520 System Setup Basic menu Function Description, Operation, Remote, Receiver for, MX703

Page 42

4. SYSTEM SETUP: Basic menu

Function

Description

 

Direct Power On

 

Allows the projector to turn on automatically once the power is fed

 

through the power cord.

 

Signal Power On

 

Sets whether to turn the projector directly on without pressing

 

POWER or ON when the projector is in standby mode and the signal

 

is feed through the VGA cable.

 

Auto Power Off

 

Allows the projector to turn off automatically if no input signal is

 

detected after a set period of time. See "Setting Auto Power Off" on

 

page 47 for details.

Operation

Quick Cooling

Enables or disables the Quick Cooling function. Selecting On enables

Settings

the function and projector cooling time will be shortened from a

 

normal 90-second duration to approximately 30 seconds.

 

This function is only available when Instant Restart is off.

 

Instant Restart

 

Selecting On enables you to restart the projector immediately within

 

90 seconds after turning it off.

 

Blank Timer

 

Sets the image blank time when the Blank feature is activated, once

 

elapsed the image will return to the screen. See "Hiding the image" on

 

page 32 for details.

 

Sleep Timer

 

Sets the auto-shutdown timer.

Remote

Allows you to enable all the remote receivers or one specific remote

Receiver (for

receiver on the projector.

MX703)

 

 

 

42 Operation

Image 42
Contents MX520/MX703 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingProjection dimensions Obtaining a preferred projected image sizeMX520 MX703 Screen size Projection distance mm Diagonal MinConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordEntering the password recall procedure Changing the passwordDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Adjusting Brilliant ColorSelecting a color temperature Setting a preferred color temperature 3D Color ManagementSetting the presentation timer Resetting current or all picture modesSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu operation Menu systemMain menu Sub-menu Options Menu Display Sec/10 sec/20 sec/30 sec/Always Time Menu Settings Menu PositionBasic Right/Bottom-LeftIP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color SystemDescription of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation Receiver forColor Splash LockBackground ScreenReset All System Setup Advanced menu Function DescriptionSettings for Baud RateCurrent SystemStatus Maintenance Care of the projectorLamp information Getting to know the lamp hourExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out ProjectorMaintenance Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Component-YP bP r input Supported timing for Video and S-Video inputsTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer