BenQ MX520 Securing the projector, Using a security cable lock, Utilizing the password function

Page 22
Password Error
Please try again.
INPUT NEW PASSWORD
MENU Back

Securing the projector

Using a security cable lock

The projector has to be installed in a safe place to prevent theft. Otherwise, purchase a lock, such as the Kensington lock, to secure the projector. You can locate a Kensington lock slot on the rear side of the projector. See item 24 on page 9 for details.

A Kensington security cable lock is usually a combination of key(s) and the lock. Refer to the lock’s documentation for finding out how to use it.

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu.

WARNING: You will be inconvenienced if you activate the password functionality and subsequently forget the password. Print out this manual (if necessary) and write the password you used in this manual, and keep the manual in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock is activated, the projector cannot be used unless the correct password is entered every time the projector is started.

1.Open the OSD menu and go to the SYSTEM SETUP: Advanced > Security Settings menu. Press MODE/ENTER. The Security Settings page displays.

2.Highlight Change Security Settings and press MODE/ENTER.

3. As pictured to the right, the four arrow keys ( , , , ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password.

4.Confirm the new password by re-entering the new password.

Once the password is set, the OSD menu

returns to the Security Settings page.

5.To activate the Power On Lock function, press / to highlight Power On Lock

and press / to select On.

IMPORTANT: The digits being input will display as asterisks on-screen. Write your selected password down here in this manual in advance or right after the password is entered so that it is available to you should you ever forget it.

Password: __ __ __ __ __ __

Keep this manual in a safe place.

6.To leave the OSD menu, press MENU/EXIT.

If you forget the password

If the password function is activated, you will be asked to enter the six-digit password every time you turn on the projector. If you enter the wrong password, the password error message as pictured to the right displays lasting for 3 seconds, and the INPUT PASSWORD message follows. You can retry by entering another six-digit password, or if you did not

record the password in this manual, and you absolutely do not remember it, you can use

22 Operation

Page 21 Page 23
Image 22
Page 21 Page 23
Contents MX520/MX703 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingObtaining a preferred projected image size Projection dimensionsMX520 MX703 Screen size Projection distance mm Diagonal MinConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordChanging the password Entering the password recall procedureDisabling the password function Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuAdjusting Brilliant Color Fine-tuning the image quality in user modesSelecting a color temperature Setting a preferred color temperature 3D Color ManagementResetting current or all picture modes Setting the presentation timerSelection Description Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMenu system Menu operationMain menu Sub-menu Options Menu Display Sec/10 sec/20 sec/30 sec/Always Time Menu Settings Menu PositionBasic Right/Bottom-LeftIP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color SystemDescription of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation Receiver forColor Splash LockBackground ScreenReset All System Setup Advanced menu Function DescriptionSettings for Baud RateSystem CurrentStatus Maintenance Care of the projectorGetting to know the lamp hour Lamp informationExtending lamp life Timing of replacing the lamp Status MessageReplacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out ProjectorMaintenance Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzSupported timing for Video and S-Video inputs Supported timing for Component-YP bP r inputTiming Copyright Warranty and Copyright informationLimited warranty Disclaimer
Top Page Image Contents