BenQ MX520 Use the handle to slowly pull the lamp out Projector, Resetting the lamp timer

Page 50

7.Use the handle to slowly pull the lamp out of

the projector.

• Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.

• Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.

•Do not insert your hands into the projector after the lamp is removed. If you touch the optical components inside, it could cause color unevenness and distortion of the projected images.

8.As shown in the figure, lower the new lamp.

9.	Reconnect the lamp connector to the
	projector.	2
10.	Tighten the screw that secures the lamp.	1
11.	Ensure the handle is fully laid flat and locked	3

in place.

• Loose screw may cause a bad connection, which could result in malfunction.

•Do not over tighten the screw.

12.Replace the lamp cover on the projector.

13.Tighten the screw that secures the lamp cover.

• Loose screw may cause a bad connection, which could result in malfunction.

• Do not over tighten the screw.

14.Connect the power and restart the projector.

Do not turn the power on with the lamp cover removed.

Resetting the lamp timer

50 Maintenance

Image 50

Contents MX520/MX703 Digital Projector Table of contents Important safety instructions Safety InstructionsSafety Instructions 3000 m Feet Ceiling mounting the projector Projector features IntroductionShipping contents Projector exterior view Front/upper side Rear/lower sideControls and functions Remote control Remote control effective range Replacing the remote control batteriesFront Table Positioning your projectorChoosing a location Front CeilingMX520 Projection dimensionsObtaining a preferred projected image size MX703 Screen size Projection distance mm Diagonal MinConnection ConnectionTerminal name Terminal appearance Connecting video source devicesConnecting audio BestOperation Starting up the projectorAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Fine-tuning the image size and clarityCorrecting keystone Using the menus Below is the overview of the OSD menuSetting a password Using a security cable lockUtilizing the password function If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Switching input signal Changing Color SpaceMagnifying and searching for details Selecting the aspect ratioAbout the aspect ratio Setting the User 1/User 2 mode Using Wall ColorSelecting a picture mode Go to the Picture Picture Mode menuSelecting a color temperature Fine-tuning the image quality in user modesAdjusting Brilliant Color Setting a preferred color temperature 3D Color ManagementSelection Description Setting the presentation timerResetting current or all picture modes Freezing the image To cancel the timer, perform the following stepsRemote paging operations Top-Left Bottom-Left Top-Right Bottom-RightLocking control keys To activate the High Altitude ModeHiding the image Operating in a high altitude environmentAdjusting the sound level Adjusting the soundUsing the test pattern Turning off the Power On/Off Ring ToneUsing the teaching templates To select Blackboard or WhiteboardDirect power off Shutting down the projectorMain menu Sub-menu Options Menu operationMenu system Menu Display Sec/10 sec/20 sec/30 sec/Always Time Menu Settings Menu PositionBasic Right/Bottom-LeftIP Address Main menu Sub-menu Options System Setup AdvancedEquivalent Lamp Hour Color SystemDescription of each menu Color Temperature Picture ModeTemperature Fine Tuning 3D ColorSettings TimerInstallation SearchRemote System Setup Basic menu Function DescriptionOperation Receiver forColor Splash LockBackground ScreenReset All System Setup Advanced menu Function DescriptionSettings for Baud RateStatus CurrentSystem Maintenance Care of the projectorExtending lamp life Lamp informationGetting to know the lamp hour Timing of replacing the lamp Status MessageReplacing the lamp Resetting the lamp timer Use the handle to slowly pull the lamp out ProjectorMaintenance Lamp events IndicatorsLight Status & Description Power events Thermal eventsTroubleshooting Specifications Projector specificationsDimensions Ceiling mount installationTiming chart Supported timing for PC inputSupported timing for Hdmi Hdcp input KHzTiming Supported timing for Component-YP bP r inputSupported timing for Video and S-Video inputs Copyright Warranty and Copyright informationLimited warranty Disclaimer