BenQ SH940 Controlling the projector through a Lan environment, If you are in a Dhcp environment

Page 37

Controlling the projector through a Lan environment

Lan Control Settings allow you to manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network.

Configuring the Lan Control Settings

If you are in a DHCP environment:

1.Take a RJ45 cable and connect one end to the RJ45 LAN input jack of the projector and the other end to the RJ45 port.

2. Press MENU on the projector or MENU/EXIT on the remote control and then press /until the Advanced Setup menu is highlighted.

3.Pressto highlight Lan Control Settings and press ENTER. The Lan Control Settings page is displayed.

4.	Press	to highlight Control By and press	/ to select RJ45.
5.	Press	to highlight DHCP and press /	to select On.

6.Press to highlight Apply and press ENTER.

7.Please wait for around 15 - 20 seconds, and then re-enter the Lan Control Settings page.

8.The Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will be displayed. Note down the IP address displayed in the Projector IP Address row.

If the Projector IP Address still does not display, contact your ITS administrator.

If you are in a non-DHCP environment:

1.	Repeat steps 1-4 above.
2.	Press to highlight DHCP and press / to select Off.

3.Contact your ITS administrator for information on the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings.

4.Press to select the item you want to modify and press ENTER.

5. Press / to move the cursor and then press / to enter the value.

6.To save the setting, press ENTER. If you do not want to save the setting, press MENU/EXIT on the remote control or EXIT on the projector.

7.Pressto highlight Apply and press ENTER.

Controlling the projector remotely through a web browser

Once you have the correct IP address for the projector and the projector is on or in standby mode, you can use any computer that is on the same local area network to control the projector.

1. Enter the address of the projector in the address bar of your browser and click Go.

English

Using the projector

37

Image 37

Contents SH940 Digital Projector Table of contents Important safety instructions Important safety instructions Avoid volatile liquids Moisture condensationDisposal Overview Shipping contentsRemote control operation Remote control batteriesCeiling mounting the projector Projector features Front and upper side view Projector exterior viewRear view Under viewControl panel Controls and functionsRemote control Choosing a location Positioning your projectorObtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensionsFloor Installation Ceiling Installation Installation for a 43 ratio screenScreen dimensions Projection distance D Lowest Highest Screen aspect ratio is 43 and the projected picture isTo use the lens shift lever Shifting the projection lensConnecting Hdmi devices Connecting with video equipmentPreparations Connecting video devices Connecting component-video/RGB devicesConnecting a monitor Connecting a computerTurning the projector on Using the projectorPreparations Selecting an input source Using the OSD menuChanging Color Space Using a security cable lock Using the menusSecuring the projector Setting a password Utilizing the password functionIf you forget the password Changing the password Entering the password recall procedureDisabling the password function Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarityCorrecting picture distortion Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture modeResetting the picture mode Setting the User 1/User 2 modeTo reset the picture mode to the preset factory values Renaming user modesFine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image claritySelecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperatureColor Management Setting Film ModeSelecting the aspect ratio Setting 3D Comb FilterAbout the aspect ratio Using Panamorph lenses optional Freezing the image Hiding the imageAdjusting the sound quality Adjusting the soundTurning off the Power On/Off Ring Tone Muting the soundControlling the projector through a Lan environment Configuring the Lan Control SettingsControlling the projector remotely through a web browser If you are in a Dhcp environmentEnter Operating in a high altitude environment To activate High Altitude ModeTo display the PIP window Displaying more than one image source simultaneouslyTurning the projector off Power II or OFF againOn-Screen Display OSD structure On-Screen Display OSD menusPicture BasicDisplay SetupSystem Dhcp Information ResolutionLoad Settings Picture ModeReset Picture SettingsYPbPr Tuning AdjustmentBlank Timer Display menuMenu Settings System Setup menuLanguage Splash ScreenClosed Caption Closed Caption EnableStandby Monitor OutLamp Settings Advanced Setup menuHdmi Settings Audio SettingsInformation menu ResolutionSource Equivalent LampCare of the projector Additional informationSetting Auto Power Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hourReplacing the lamp Timing of replacing the lampStatus Message English Resetting the lamp timer Power events IndicatorsLight Status & Description Problem Cause Remedy TroubleshootingGeneral characteristics SpecificationsOptical ElectricalCeiling mount installation DimensionsSupported timing for PC input Timing chartFormat Refresh rateFormat Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Hdmi Hdcp input Supported timing for Edtv and Hdtv via Component inputsWarranty Warranty and Copyright informationCopyright Disclaimer