BenQ SH910 Picture menu, Picture Mode, Reference, Brightness, Contrast, Color, Tint, Sharpness

Page 65

2. PICTURE menu

	FUNCTION)	DESCRIPTION
	Picture Mode	Pre-defined picture modes are provided so you can optimize your
	Picture Mode	projector image set-up to suit your program type. See "Selecting a
		picture mode" on page 31 for details.

		Selects a picture mode that best suits your need for the image quality
	Reference	and further fine-tune the image based on the selections listed on the
	Reference	same page below. See "Setting the User 1/User 2 mode" on page 31 for
	Mode	details.
		This function is only available when User 1 or User 2 is selected.

		Adjusts the brightness of the image. See "Adjusting Brightness" on
	Brightness	page 32 for details.
	Brightness	This function is only available when User 1 or User 2 is selected.


		Adjusts the degree of difference between dark and light in the image.
	Contrast	See"Adjusting Contrast" on page 32 for details.
	Contrast	This function is only available when User 1 or User 2 is selected.


		Adjusts the color saturation level -- the amount of each color in a
		video image. See "Adjusting Color" on page 32 for details.
	Color	This function is only available when User 1 or User 2 is selected.
		This function is only available when a Video or S-Video signal is
		selected and the system format is NTSC or PAL.
		Adjusts the red and green color tones of the image. See "Adjusting
		Tint" on page 32 for details.
	Tint	This function is only available when User 1 or User 2 is selected.
		This function is only available when a Video or S-Video signal is
		selected and the system format is NTSC or PAL.
		Adjusts the image to make it look sharper or softer. See "Adjusting
	Sharpness	Sharpness" on page 32 for details.
	Sharpness	This function is only available when User 1 or User 2 is selected.

Operation 65

Image 65

Contents SH910 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Network Setting Remote controlUp/Down TestOperating the Laser pointer VolumeMute InfoReplacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection ConnectionConnection Video Normal Connecting Video source devicesStarting up the projector OperationAuto-adjusting the image Adjusting the projected imageAdjusting the projection angle Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusUtilizing the password function Using a security cable lockSetting a password If you forget the passwordDisabling the password function Entering the password recall procedureChanging the password Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Setting the User 1/User 2 mode Selecting a picture modeGo to the Picture Picture Mode menu Optimizing the imageFine-tuning the image quality in user modes Using Wall ColorPress MODE/ENTER and the 3D Color Management page displays About color temperatures3D Color Management Remote paging operations Setting the Sleep TimerHiding the image Freezing the imageAdjusting the sound level Adjusting the soundTo activate the High Altitude Mode Operating in a high altitude environmentAdjusting the microphone’s sound level Turning off the Power on/off ring toneHighlight Power on/off Ring Tone and select Off Turning on/off the SRSPersonalizing the projector menu display Displaying more than one image source simultaneouslyShutting down the projector Configuring the Wireless LAN Settings Configuring the Wired LAN SettingsControlling the projector through a LAN environment If you are in a Dhcp environmentControlling the projector remotely through a web browser Click Download to save Q Presenter software on your computer Operation Operation Iii Operation Operation Operation Operation Displaying image through Q Presenter Operation Operation Vii Using the Web Control Lock Using the Projection Login Code Image File Types Presenting From a USB ReaderPreparation Controlling USB ReaderGo to previous or next image PressOperation Remote Desktop Control through Q Presenter Enter Menu system Menu operationSource System Setup BasicSRS System Setup AdvancedAdvanced SetupDescription of each menu Picture menu Picture ModeReference ModeSave Settings TemperatureSource 2. Picture menu Brilliant ColorAuto Power Off Direct Power OnBlank Timer Sleep TimerReceiver RemoteBackground Color Splash ScreenHigh Altitude System Setup Advanced menuAudio LampTest Pattern Baud RateClosed CaptionNetwork Reset AllCurrent Information menuSystem StatusCare of the projector MaintenanceSetting Auto Power Off Setting Lamp Mode as EconomicLamp information Getting to know the lamp hourStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp Cover removed Tighten the screws that secure the lamp Resetting the lamp timerIndicators Troubleshooting Optical SpecificationsCeiling mount screws M4 x 8 Max. L = 8 mm Unit mm DimensionsCeiling mount installation Supported timing for PC input Timing chart640 x Supported timing for Hdmi inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputLimited warranty Warranty and Copyright informationPatents for SH910 CopyrightFCC statement Regulation statementsEEC statement for European users Weee directiveRegulation statements Regulation statements