BenQ SH910 user manual Timing of replacing the lamp, Status Message

Page 75

Timing of replacing the lamp

When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.

Go to http://lamp.benq.com for a replacement lamp.

The Lamp indicator light will light up if the lamp becomes too hot. See "Indicators" on page 79 for details.

The following lamp warning displays will remind you to change the lamp.

The warning messages below are for reference only. Please follow the actual on-screen instructions to prepare and replace the lamp.

Status	Message
Install a new lamp for optimal performance. If the
projector is normally run with Economic selected
("Setting Lamp Mode as Economic" on page 74),
you may continue to operate the projector until
the next lamp warning appears.
Press MODE/ENTER to dismiss the message.

A new lamp should be fitted to avoid the
inconvenience when the projector runs out of
lamp time.
Press MODE/ENTER to dismiss the message.

It is strongly recommended that you replace the
lamp at this stage. The lamp is a consumable item.
The lamp brightness diminishes with use. This is
normal lamp behavior. You can replace the lamp
whenever you notice that the brightness level has
significantly diminished.
Press MODE/ENTER to dismiss the message.

The lamp MUST be replaced before the projector
will operate normally.
Press MODE/ENTER to dismiss the message.

"XXXX" shown in the above messages are numbers that vary depending on different models.

Maintenance 75

Image 75

Contents SH910 Digital Projector WelcomeTable of contents Important safety instructions Safety Instructions Do not block the ventilation holes Safety Instructions Introduction Projector featuresShipping contents Front/upper side Projector exterior viewProjector Controls and functionsCeiling mounting the projector Test Remote controlNetwork Setting Up/DownInfo VolumeOperating the Laser pointer MuteReplacing the remote control battery Choosing a location Positioning your projectorObtaining a preferred projected image size Positioning your projector Min. zoom Projection dimensionsConnection ConnectionConnection Video Normal Connecting Video source devicesStarting up the projector OperationAdjusting the projected image Adjusting the projection angleAuto-adjusting the image Correcting keystone Fine-tuning the image size and clarityUse / to highlight the System Setup Basic menu Using the menusIf you forget the password Using a security cable lockUtilizing the password function Setting a passwordEntering the password recall procedure Changing the passwordDisabling the password function Changing Color Space Switching input signalSelecting the aspect ratio Magnifying and searching for detailsAbout the aspect ratio Optimizing the image Selecting a picture modeSetting the User 1/User 2 mode Go to the Picture Picture Mode menuFine-tuning the image quality in user modes Using Wall ColorAbout color temperatures 3D Color ManagementPress MODE/ENTER and the 3D Color Management page displays Freezing the image Setting the Sleep TimerRemote paging operations Hiding the imageOperating in a high altitude environment Adjusting the soundAdjusting the sound level To activate the High Altitude ModeTurning on/off the SRS Turning off the Power on/off ring toneAdjusting the microphone’s sound level Highlight Power on/off Ring Tone and select OffPersonalizing the projector menu display Displaying more than one image source simultaneouslyShutting down the projector If you are in a Dhcp environment Configuring the Wired LAN SettingsConfiguring the Wireless LAN Settings Controlling the projector through a LAN environmentControlling the projector remotely through a web browser Click Download to save Q Presenter software on your computer Operation Operation Iii Operation Operation Operation Operation Displaying image through Q Presenter Operation Operation Vii Using the Web Control Lock Using the Projection Login Code Controlling USB Reader Presenting From a USB ReaderImage File Types PreparationGo to previous or next image PressOperation Remote Desktop Control through Q Presenter Enter Menu system Menu operationSource System Setup BasicSRS System Setup AdvancedAdvanced SetupDescription of each menu Mode Picture ModePicture menu ReferenceBrilliant Color TemperatureSave Settings Source 2. Picture menuSleep Timer Direct Power OnAuto Power Off Blank TimerColor Splash Screen RemoteReceiver BackgroundLamp System Setup Advanced menuHigh Altitude AudioCaption Baud RateTest Pattern ClosedNetwork Reset AllStatus Information menuCurrent SystemCare of the projector MaintenanceGetting to know the lamp hour Setting Lamp Mode as EconomicSetting Auto Power Off Lamp informationStatus Message Timing of replacing the lampReplacing the lamp Do not turn the power on with the lamp Cover removed Tighten the screws that secure the lamp Resetting the lamp timerIndicators Troubleshooting Optical SpecificationsDimensions Ceiling mount installationCeiling mount screws M4 x 8 Max. L = 8 mm Unit mm Supported timing for PC input Timing chart640 x Supported timing for Hdmi inputSupported timing for Video and S-Video inputs Supported timing for Component-YPbPrinputCopyright Warranty and Copyright informationLimited warranty Patents for SH910Weee directive Regulation statementsFCC statement EEC statement for European usersRegulation statements Regulation statements