Pre-programming remote controller, Mode, Level

Pre-programming remote controller

Learning a pre-programming code

Controlling a DVD player

You can make RC-446M remote controller to operate a product from other brand than Onkyo by storing the pre-programming code of the brand in the RC-446M.

1.Find the 2-digit number for the brand name of the component that you want to operate in the table on page 33.

2.Turn on the component that you want to operate (i.e. DVD, satellite tuner, or television).

3.While holding down the MODE button on the RC-446M that you want to program, press the LEVEL 5 button, and then release both buttons.

4.Within 30 seconds, enter the 2-digit code number.

To enable entry of the 2-digit code number, some of the remote controller keys become the numeric keys with the assignment as shown in the figure.

Buttons with programmed usage and operations are the same as the operational buttons on page 31.

When entering the code of Onkyo DVD players

There are three SETTING numbers. Choose the SETTING number according to how you will be using the DVD player.

No. 02/03: These codes are for operating the Onkyo DVD player by pointing the remote controller directly at it, either because it does not have an zconnector, or it does but you are not using an

zcable and connecting it. With the initial setting of the RC-446M, the code is set to 03. If it does not operate properly, enter 02.

No. 01: This code is for Onkyo DVD players that have an z connector that you are connecting to the HT-R490 with an z cable. You will then operate the DVD player by pointing the remote controller at the remote control sensor on the HT-R490.

With the initial setting of the RC-446M, the code is set to 03. When the DVD player is connected with z connecter of the HT-R490, you will need to change the code to 01.

5.Press some operation buttons for the component that you want to operate to check if the system operates properly.

If the system operates properly, the code is correct. If the component does not operate properly, return to step 3.

STANDBY/ ON	SLEEP	DIMMER	DISPLAY
	INPUT SELECTOR
CD	TAPE		TUNER
D V D	VIDEO 1	VIDEO 2
			TUNER
SUR MODE SW MODE AUDIO SEL PRESET
	MODE		VCR
TV	CABLE SATELLITE		VCR
STANDBY/ ON	DVD	CD	TAPE	MODE
CH	TV VOL		CH
				1	2	3
DISC			MUTING
				4	5	6
TV/ VCR	TV VOL
				7	8	9
TOP MENU	E N T E R	MENU
	E N T E R				0
		VOLUME			0
RETURN		SETUP
TEST TONE CH SEL		LEVEL		LEVEL 5
				LEVEL 5
REMOTE CONTROLLER
	RC-446M

Notes:

•With some brand’s components, some buttons may not work correctly.

•If more than one code is given in the table, try the code one by one until you reach the code for your component (i.e. if the

first code does not work, then try the next).

Controlling a TV/VCR/Cable TV/Satellite tuner

1.Press the desired MODE button.

2.Press the STANDBY/ON button to turn on the device.

3.Press the desired operation button.

TV mode
CH+	: Changes the TV channel upward.
CH–	: Changes the TV channel downward.
TV VOL+ : Increases the TV volume.
TV VOL–	: Decrease the TV volume.
TV/VCR	: Switches the TV/VCR inputs.

VCR mode

CH+	: Changes the received channel upward.
CH–	: Changes the received channel downward.

s: Starts playback of videotape.

e: Stops playback, recording, fast forward or rewinding.

f: Fast-forwards the videotape.

d: Rewinds the videotape.

2/8 : Lets playback pause temporarily.

CABLE/SAT mode

CH+ : Changes the received channel upward.

CH– : Changes the received channel downward.