3M MP8747, MP8746 manual Introduction, Intended Use, Important Safeguards

Page 4

Introduction

Intended Use

Before operating the machine, please read this entire manual thoroughly. The 3MPersonal Projector MP8746/MP8747 was designed, built, and tested for use indoors, using 3M lamps, 3M ceiling mount hardware, and nominal local volt- ages. The use of other replacement lamps, outdoor operation, operation in environments containing heavy cigarette smoke or different voltages has not been tested and could damage the projector or peripheral equipment and/or create a potentially unsafe operating condition.

Important Safeguards

1.Read and understand all instructions before using. Pay particular attention to areas where these symbols are shown:

WARNING

Indicates a potentially hazardous situation which,

if not avoided, could result in death or serious injury.

 

Indicates a potentially hazardous situation which, if not

Caution avoided, could result in minor or moderate injury. It may also be used to alert against unsafe practices.

Note - Used to emphasize important conditions or details.

2.Close supervision is necessary when any appliance is used by or near children. Do not leave appliance unattended while in use.

3.Never look directly into the projector lens when the lamp is on. The lamp produces a strong light that could damage your eyesight.

4. Care must be taken, as burns can occur from touching hot parts.

5. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged, until it has been examined by a qualified service technician.

6. Position the cord so that it will not be tripped over, pulled or placed in contact with hot surfaces.

7.If an extension cord is necessary, a cord with a current rating at least equal to that of the appliance should be used. Cords rated for less amperage than the appliance may overheat.

8.Always unplug appliance from electrical outlet before cleaning and servicing and when not in use. Grasp plug and pull to disconnect.

9.To reduce the risk of electric shock, do not immerse this appliance in water or other liquids.

10.To reduce the risk of electric shock, do not disassemble this appliance. Take it to a qualified technician when service or repair work is required. Incorrect reassembly can cause electric shock when the appliance is subsequently used.

11.Connect this appliance to a grounded outlet.

12.Do not expose this projector to direct sunlight or use it outside.

13. Keep all ventilation openings free of any obstructions.

14.Always open the lens shutter or remove the lens cap when the projector lamp is on.

15.Do not look directly into light beam of laser pointer. The pointer produces a strong light which could damage your eyesight.

16.The projection lamp contains mercury. Always dispose of it in a proper manner according to local regulations.

17.To prevent lamp from bursting, do not continue using the same lamp after changing the mounting position of the projector (desktop to ceiling mount or ceiling mount to desktop mount).

18.Always operate machine on a flat, sturdy surface.

4

3MPersonal Projector MP8746/MP8747

© 3M IPC 2000

 

 

 

Image 4
Contents MP8746/MP8747 Personal Projector This page intentionally left blank for printed version Table of Contents Introduction Important SafeguardsIntended Use Location of Product Safety Labels U T I O NWarranty Limited Warranty Thank You for Choosing 3MLimitation Of Liability Patents, Trademarks & CopyrightsContents of Shipping Box Optional AccessoriesUnpack Keep Your Packing MaterialsMachine Characteristics Product DescriptionPart Identification List Control Panel Keypad ButtonsPowerCable System Setup-Connecting to Various EquipmentRGB Signal input video from computer Remote Control Transmitter Identification STANDBY/ONChanging Remote Control Battery Mouse EmulationRemote Control Mouse Function Mouse Projector Accessory Cable PC Connector Control/USBAttaching the Handle For USBProjector Start-up Basic OperationsProjector Shutdown How to Use Height Adjustment Foot Adjustments and FunctionsScreen Chart Reset Function Plug & Play FunctionFreeze Function Magnify FunctionFactory Default Setting Menu NavigationSetup Submenu ColorbalhtintsizeAuto Input SubmenuOPT Image SubmenuOPT OPT. SubmenuMaintenance Cleaning the Air FilterCleaning the Inner Components Cleaning the LensLamp Reset Lamp HoursDisplay Lamp Operation Hours Power cord before changing lamp Replacing the LampTroubleshooting Symptoms/SolutionsMessages/Solutions Error Message Displays Cause SolutionIndicator Lights Power Lamp TempAccessories Service InformationAccessories Part Number How to OrderDimension Diagram RGB Signal Pin AssignVideo Signal Pin Assign Technical AppendixVesa Initial Set Signals Computer/SignalUSB Mouse Connection to the Mouse Control PS/2, ADB or Serial MousePS/2 Mouse Connection to the Mouse Control ADB Mouse Serial MouseCommunications Setting 19200bps, 8N1 Protocol Command dataRS-232 Communication HeaderRequesting projector status Get command Changing the projector settings Set commandUsing the projector default settings Reset command Increasing the projector setting value Increment commandCRC Be EF CRC Ntsc Page Important Notice