Connecting the Antennas, Connecting the Power Cord

Onkyo TX-NR709 Connecting the Antennas, Connecting the Power Cord, Taiwan models

Page 21

Connecting the Antennas

This section explains how to connect the supplied indoor FM antenna and AM loop antenna.

The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

Caution		North American and
		Taiwan models
• Be careful not to injure yourself when using
thumbtacks.

European, Australian and Asian models

			Insert the plug fully
Push.	Insert wire.	Release.	into the jack.

Insert the plug fully into the jack.

Assembling the AM loop antenna

Thumbtacks, etc.

AM loop antenna (supplied)

Indoor FM antenna (supplied)

Note

•Once your AV receiver is ready for use, you’ll need to tune into a radio station and position the antenna to achieve the best possible reception.

•Keep the AM loop antenna as far away as possible from your AV receiver, TV, speaker cables, and power cords.

Tip

•If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available outdoor FM antenna instead.

•If you cannot achieve good reception with the supplied indoor AM loop antenna, try using it with a commercially available outdoor AM antenna.

Connecting the Power Cord

1 (European, Australian, Asian and Taiwan models) Connect the supplied power cord to the AV receiver’s AC INLET.

To AC wall outlet

2 Plug the power cord into an AC wall outlet.

Note

•Before connecting the power cord, connect all of your speakers and AV components.

•Turning on the AV receiver may cause a momentary power surge that might interfere with other electrical equipment on the same circuit. If this is a problem, plug the AV receiver into a different branch circuit.

•Do not use a power cord other than the one supplied with the AV receiver. The supplied power cord is designed exclusively for use with the AV receiver and should not be used with any other equipment.

•Never disconnect the power cord from the AV receiver while the other end is still plugged into a wall outlet. Doing so may cause an electric shock. Always disconnect the power cord from the wall outlet first, and then the AV receiver.

Image 21

Contents

TX-NR709 10 cm 4 at the rear. The rear edge of the shelf or Local regulations when disposing of batteriesBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Make sure you have the following accessories Supplied AccessoriesInstalling the batteries Aiming the remote controllerContents Services available may vary depending on the region FeaturesAmplifier ProcessingTHX Select2 Plus Front Panel Front & Rear PanelsFor detailed information, see the pages in parentheses DisplayRear Panel Front L/R, CENTER, Surr L/R, SB/FH/FW* L/R, SubwooferZone 2 Line OUT jacks Controlling the AV Receiver Remote ControllerDimmer button Display button Muting button Controlling the tunerConnecting Your Speakers Connecting the AV ReceiverConnecting the Speaker Cables Screw-type speaker terminalsSpeaker Connection Precautions Speaker ConfigurationAttaching the Speaker Cable Labels Number SpeakersUsing a Powered Subwoofer Using Dipole SpeakersBi-amping the Front Speakers TipConnecting a Power Amplifier About AV Connections Connecting AV componentsAV Cables and Jacks Hdmi cable Connecting Components with Hdmi Audio Return Channel ARC function Jack Components Assignable E F G H Connecting Your ComponentsJack/Port Components Assignable How to record a video sourceConnecting a Recording Component Connecting Onkyo uComponentsSystem On/Auto Power On Remote ControlConnecting the Power Cord Connecting the AntennasPlug the power cord into an AC wall outlet Taiwan modelsTurning On Turning On/Off the AV ReceiverTurning Off AV receiver comes on, the display lightsControlling Contents of USB or Network Devices Selecting the Language for the Onscreen Setup MenusPlayback Playing the Connected ComponentUnderstanding Icons on the Display Playing an iPod/iPhone via USBEnter Listening to Internet Radio Playing a USB DeviceListening to Other Internet Radio Registering My Favorites*1Top menu of Internet Radio Windows Media Player 12 Setup Windows Media Player 11 SetupPlaying Music Files on a Server Remote PlaybackUsing the Tuner Using Remote PlaybackTuning into Radio Stations Listening to AM/FM RadioPresetting AM/FM Stations Using RDS excluding North American and Taiwan modelsMode Displaying Radio Text RT Finding Stations by Type PTYListening to Traffic News TP Using the Automatic Speaker Setup Using Basic FunctionsMeasurement procedure First measurement positionAdjust the subwoofer volume level to 75 dB When you’ve finished making the settings, press` Cancel Use q/wto select a target, and use e/rto change the settingChanging the Speaker Setup Manually Error MessagesSelecting Listening Modes Using the Listening ModesAbout Listening Modes Following audio formats are supported by the listening modeExplanatory Notes Input SourceOnkyo-Original DSP Listening Modes Listening ModesZXC DSD*6 DTSListening Mode Description Input Speaker Source Layout Neo6 Audyssey DSX *8THX Used. The Neo6 indicator lights on the display Listening Mode Description Input Speaker Source LayoutFor 7.1-channel playback Sources for 6.1/7.1-channel playbackUsing the Home Menu Using the Sleep TimerSetting the Display Brightness Displaying Source Information Using HeadphonesChanging the Input Display Selecting Speaker LayoutRecording Using Easy MacrosOn-screen Setup Menus Advanced SetupCommon Procedures in Setup Menu Explanatory NotesMonitor Out Input/Output AssignSUB Hdmi OUT SUBHdmi Input Here are the default assignmentsComponent Video Input BD/DVD, VCR/DVR, CBL/SAT, GAME, PC TV/CD, PHONO, PortSpeaker Settings Speaker SetupDigital Audio Input Analog Audio InputFront Subwoofer PhaseCenter*1, Surround*1, Surround Back*2*3*4 Front Wide*1*2*4, Front High*1*2*4Speaker Distance Wireless SubwooferLevel Calibration UnitEqualizer Settings THX Audio SetupBGC Audio Adjust Multiplex/MonoDolby Theater-Dimensional Audyssey DSXLFE Level Audyssey Source SetupIntelliVolume SyncName Edit To correct a character Picture AdjustWide Mode*1*2 Picture Mode*1Audio Selector Charge Mode Listening Mode PresetVolume Setup Hardware SetupOSD Setup MiscellaneousAM/FM Frequency Step North American and Taiwan models TunerAM Frequency Step European, Australian and Asian models Hdmi ControlRIHDAudio TV Out Auto StandbyAudio Return Channel Lip SyncFirmware Update NetworkDhcp Remote Controller Setup Lock SetupUsing the Audio Settings Audyssey Music Optimizer Late NightRe-EQ Connecting the Zone Speakers to an Additional Amplifier Connecting Your Zone 2 Speakers Directly to the AV receiverZone Making Zone 2 ConnectionsAdjusting the Volume for Zone Operating on the remote controllerControlling Zone 2 Components Using a Multiroom Kit with a Cabinet Using a Multiroom Kit with ZoneMuting Zone Press ZONE2 followed by MutingUsing the Onkyo Dock IPod/iPhone Playback via Onkyo DockUP-A1 Dock RI Dock Controlling Your iPod/iPhoneRepeat Random Display Available buttonsMenu ModeLooking up for Remote Control Code Preprogrammed Remote Control CodesEntering Remote Control Codes Controlling Other ComponentsResetting Remote Mode Buttons Remote Control Codes for Onkyo Components Connected via uResetting the Remote Controller Controlling Other ComponentsVCR/PVR Enter Setup Search Repeat Random Mode8SOURCE*1 Input Guide TOP MenuDeleting Acquired Commands Learning CommandsFollowing buttons cannot learn new commands RemoteMaking Macros Using Normal MacrosRunning Macros Deleting MacrosTroubleshooting PowerAudio Can’t select the Pure Audio listening mode There’s no sound with a certain signal formatSpeaker volume cannot be set as required About DTS signalsRemote Controller VideoTuner Recording UP-A1 Dock for iPod/iPhoneZone Music Server and Internet RadioOthers USB Device PlaybackComponent Video Monitor OUT Important Note Regarding Video PlaybackUpdate procedure Firmware UpdateUpdating the Firmware via Network Before you startErrors during an update via network TroubleshootingError Code Description Updating the Firmware via USBOnkyo Sound & Vision Corporation Errors during an update via USBVideo Connection Formats Connection Tips and Video Signal PathOUT Audio Connection FormatsOutput Video Resolution Chart4K *2 1080p/24 1080i 720p 480p/576p 480i/576i 1080p 1080i 720p 480p/576p 480i/576iUsing an RIHD-compatible TV, Player, or Recorder About p-compatible componentsOperations that can be performed with Connection Confirm the connecting and setting How to connect and setupConfirm the settings Operate with the remote controllerAbout Hdmi Supported Audio FormatsAbout Copyright Protection Network/USB Features Connecting to the NetworkNetwork Requirements USB Device Requirements Server RequirementsServer playback Remote playbackAbout Dlna Supported Audio File FormatsAmplifier Section Tuner Section SpecificationsVideo Section GeneralOthers Audio OutputsMemo Memo 4 0 0 6 9

Related manuals

Onkyo TX-NR709 Connecting the Antennas, Connecting the Power Cord, Taiwan models