External Control Device Setup
01. Power (Command:a)
GTo control Power On/Off of the Monitor.
Transmission
[k][a][ ][Set ID][ ][Data][Cr]
Data 0 : Power Off | 1 : Power On |
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
G To show Power On/Off.
Transmission
[k][a][ ][Set ID][ ][FF][Cr]
Data 0 : Power Off | 1 : Power On |
Acknowledgement
[a][ ][Set ID][ ][OK][Data][x]
*In a like manner, if other functions transmit ‘FF’ data based on this format, Acknowledgement data feedback presents status about each function.
02. Input Select (Command:b) (Main Picture Input)
GTo select input source for the Monitor.
You can also select an input source using the INPUT SELECT button on the Monitor's remote control.
Transmission
[k][b][ ][Set ID][ ][Data][Cr]
Data | 0 | : RGB | 3 | : |
| 1 | : Component | 4 | : DVI |
| 2 | : Video |
|
|
Acknowledgement |
|
| ||
|
|
|
| |
[b][ | ][Set ID][ ][OK][Data][x] |
|
| |
|
|
|
|
|
03. Aspect Ratio (Command:c) (Main Picture Format)
G To adjust the screen format.
You can also adjust the screen format using the ARC (Aspect Ratio Control) button on remote control or in the Special menu.
Transmission
[k][c][ ][Set ID][ ][Data][Cr]
Data 0 : Wide screen (16:9)
1: Normal screen (4:3)
2: Full screen (Zoom)
3: Horizon
Acknowledgement
[c][ ][Set ID][ ][OK][Data][x]
*You select either 16:9 or 4:3 screen aspect ratio using the PC, DTV 720p/1080i.
04. Screen Mute (Command:d)
G To select screen mute on/off.
Transmission
[k][d][ ][Set ID][ ][Data][Cr]
Data 0 : Screen mute off (Picture on) 1 : Screen mute on (Picture off)
Acknowledgement
[d][ ][Set ID][ ][OK][Data][x]
05. Volume Mute (Command:e)
G To control volume mute on/off.
You can also adjust mute using the MUTE button on remote control.
Transmission
[k][e][ ][Set ID][ ][Data][Cr]
Data 0 : Volume mute on (Volume off) 1 : Volume mute off (Volume on)
Acknowledgement
[e][ ][Set ID][ ][OK][Data][x]
06. Volume Control (Command:f)
G To adjust volume.
You can also adjust sound level with the volume but- tons on remote control.
Transmission
[k][f][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•Refer to ‘Real Data Mapping1’ as shown below.
Acknowledgement
[f][ ][Set ID][ ][OK][Data][x]
07. Contrast (Command:g)
GTo adjust screen contrast.
You can also adjust contrast in the Video menu.
Transmission
[k][g][ ][Set ID][ ][Data][Cr]
Data Min : 0 ~ Max : 64
•Refer to ‘Real Data Mapping1’ as shown below.
Acknowledgement
[g][ ][Set ID][ ][OK][Data][x]
*Real Data Mapping 1 0 : Step 0
A : Step 10 (SET ID 10)
F: Step 15 (SET ID 15)
10 : Step 16 (SET ID 16)
64 : Step 100
Owner’s Manual 27