LG Electronics MT-50PZ40, MT-50PZ41, MT-50PZ43S, MZ-50PZ42, MZ-50PZ43 Installing Batteries

Page 11

Controls of the remote control

-When using the remote control aim it at the remote control sensor of the Monitor.

-There’s maybe defect in consecutive operation of remote control in specified brightness according to this monitor fea- ture.

1.POWER

switches the set on from standby or off to standby.

2.SLEEP

sets the sleep timer.

1

2

3

4

5

6

7

8

9

10

11

12

POWER

 

 

SLEEP

 

INPUT SELECT

PSM

 

SSM

ARC

 

PIP ARC

PIP

TWIN PICTURE

SWAP

 

SUB INPUT

MENU

 

MUTE

VOL

OK

VOL

 

1

2

3

4

5

6

7

8

9

 

0

 

POWER

STOP

P/STILL

REW

PLAY

FF

 

 

REC

WIN.SIZE

WIN.POSITION SPLIT ZOOM

ZOOM -

ZOOM +

13

14

15

16

17

18

19

20

3.PSM (Picture Status Memory) recalls your preferred picture setting.

4.ARC (Aspect Ratio Control) changes the picture format.

5.PIP

switches the sub picture on or off.

6.SWAP

alternates between main and sub picture.

7.MENU Button selects a menu.

8.D / E

selects a menu item.

F / G (Volume Down/Up) adjusts the volume. adjusts menu settings.

OK

displays the current mode.

9.NUMBER BUTTONS

10.VCR BUTTONS

control a LG video cassette recorder.

11.WIN. SIZE

adjusts the sub picture size.

12.ZOOM-/ZOOM+

13.INPUT SELECT BUTTON

selects TV, AV or PC monitor mode.

14.SSM (Sound Status Memory) recalls your preferred sound setting.

15.PIP ARC

changes the picture format of PIP.

16.TWIN PICTURE

17.SUB INPUT

selects the input mode for the sub picture.

18.MUTE Button

switches the sound on or off.

19.SPLIT ZOOM

enlarge the screen with regular ration.

20.WIN.POSITION

moves the sub picture to D / E or F / G direction.

Installing Batteries

• Open the battery compartment cover on the back side and insert the batteries with correct polarity.

• Apply two 1.5V alkaline batteries of AAA type. Don’t mix the used batteries with new batteries.

• Install the batteries with the correct polarities.

11

Image 11
Contents Plasma Monitor LG Plasma Monitor Contents Do not insert any object into the exhaust vent Safety InstructionsDo not use water the Monitor while cleaning Earth wire should be connectedOnly use the specified batteries Do not pull the cord but the plug when unpluggingObjects like a heater Back Panel Controls of the MonitorFront Panel Controls External Speaker 8 ohm output Watching External EquipmentsBack Panel RCA Type Scart TypeHow to connect Watching VCR When the Interface board is installedWatching Cable TV When the Interface board is installed Watching DVD When the Interface board is installedPC Setup Connecting PCSetup Instructions to Connect a PC to your Monitor RGB2 mode Resolution Horizontal Vertical Displayable Monitor SpecificationRGB1 mode Resolution Horizontal Vertical Resolution Horizontal VerticalInstalling Batteries Controls of the remote controlOptional Extras AccessoriesTo install as desktop type Monitor InstallationTo install as wall mounting type Adjusting volume level Menu language setupTurning on the Monitor just after installation Turning on the Monitor power cord is still connectedPSM Picture Status Memory Adjusting Auto Colour ControlManual Colour Temperature ControlUser option Video MenuAudio Menu AVL Auto Volume LevelerAdjusting Sound Manual Setting Press the SSM button to select the picture appearance setupTime Menu Setting the ClockSetting the On/Off Timer Sleep TimerWhite Wash Special MenuChild lock OrbiterSplit Zoom Auto adjustment RGB1PC mode onlySetting Picture Format Screen MenuScreen Position Manual Configure RGB1PC mode onlyInitializing Reset to factory value PIP Function Swapping the Twin Picture Sub Picture Size AdjustmentTwin Picture Selecting a source for the Twin pictureSet ID External Control Device SetupType of connector D-Sub 9-pin male RS-232C configurationsTransmission / Receiving Protocol Command Reference ListPower Commanda Input select Commandb Main picture inputVolume control Commandf Aspect Ratio Commandc Main picture formatScreen mute Commandd Volume mute CommandeRemote control lock mode Commandm Sharpness CommandkPIP Size Commando OSD select CommandlGreen Adjustment Commandw Balance CommandtColour temperature Commandu Red Adjustment CommandvReal data mapping Orbiter Time Setting CommandrOrbiter Pixel Setting Commands Real data mapping 1 0 StepPage No output from one Troubleshooting check listNo picture No soundModel Product specifications