LG Electronics MT-50PZ40, MT-50PZ41, MT-50PZ43S, MZ-50PZ42, MZ-50PZ43 Objects like a heater

Page 5

*Safety instructions have two kinds of information, and each meaning of it is as below.

WARNING The violation of this instruction may cause serious injuries and even death.

The violation of this instruction may cause light injuries or damage of the NOTES product.

Take care of danger that may happen under specific condition.

NOTE

This plasma display is designed to be mounted hori- zontally (wide viewing).

Never touch the power plug with a wet hand.

- This may cause an electric shock.

Disconnect from the mains and remove all connec- tions before moving.

Do not place the Monitor in a built-in installation such as a bookcase or rack.

- Ventilation required.

objects like a heater.

- This may cause a fire or an electric shock.

Do not plug when the power cord or the plug is dam- aged or the connecting part of the power outlet is loose.

- This may cause a fire or an electric shock.

Dispose of used batteries carefully to protect a child from eating them.

- In case that it eats them, take it to see a doctor immediately.

When moving the Monitor assembled with speakers do not carry holding the speakers.

-This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor.

Unplug this product from the wall outlet before clean- ing. Do not use liquid cleaners or aerosol cleaners.

-This may cause damaged the Monitor or could give an electric shock.

When installing the Monitor on a table, be careful not to place the edge of its stand.

-This may cause the Monitor to fall, causing serious injury to a child or adult, and serious damage to the Monitor.

Do not place an outside antenna in the vicinity of over- head power lines or other electric light or power cir- cuits.

- This may cause an electric shock.

There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls.

- This may cause an electric shock.

Do not pull the cord but the plug when unplugging.

- This may cause a fire.

Ensure the power cord doesn’t trail across any hot

Contact the service center once a year to clean the internal part of the Monitor.

- Accumulated dust can cause mechanical failure.

The distance between eyes and the screen should be about 5 ~ 7 times as long as diagonal length of the screen.

- If not, eyes will strain.

Unplug the Monitor from the wall outlet when it is left unattended and unused for long periods of time.

-Accumulated dust may cause a fire or an electric shock from deterioration or electric leakage.

Only use the specified batteries.

-This make cause damaged the Monitor or could give an electric shock.

5

Image 5
Contents Plasma Monitor LG Plasma Monitor Contents Do not use water the Monitor while cleaning Safety InstructionsEarth wire should be connected Do not insert any object into the exhaust ventOnly use the specified batteries Do not pull the cord but the plug when unpluggingObjects like a heater Back Panel Controls of the MonitorFront Panel Controls Back Panel RCA Type Watching External EquipmentsScart Type External Speaker 8 ohm outputWatching Cable TV When the Interface board is installed Watching VCR When the Interface board is installedWatching DVD When the Interface board is installed How to connectPC Setup Connecting PCSetup Instructions to Connect a PC to your Monitor RGB1 mode Resolution Horizontal Vertical Displayable Monitor SpecificationResolution Horizontal Vertical RGB2 mode Resolution Horizontal VerticalInstalling Batteries Controls of the remote controlOptional Extras AccessoriesTo install as desktop type Monitor InstallationTo install as wall mounting type Turning on the Monitor just after installation Menu language setupTurning on the Monitor power cord is still connected Adjusting volume levelManual Colour Temperature ControlUser option Adjusting Auto Colour ControlVideo Menu PSM Picture Status MemoryAdjusting Sound Manual Setting AVL Auto Volume LevelerPress the SSM button to select the picture appearance setup Audio MenuSetting the On/Off Timer Setting the ClockSleep Timer Time MenuChild lock Special MenuOrbiter White WashSetting Picture Format Auto adjustment RGB1PC mode onlyScreen Menu Split ZoomScreen Position Manual Configure RGB1PC mode onlyInitializing Reset to factory value PIP Function Twin Picture Sub Picture Size AdjustmentSelecting a source for the Twin picture Swapping the Twin PictureType of connector D-Sub 9-pin male External Control Device SetupRS-232C configurations Set IDPower Commanda Command Reference ListInput select Commandb Main picture input Transmission / Receiving ProtocolScreen mute Commandd Aspect Ratio Commandc Main picture formatVolume mute Commande Volume control CommandfPIP Size Commando Sharpness CommandkOSD select Commandl Remote control lock mode CommandmColour temperature Commandu Balance CommandtRed Adjustment Commandv Green Adjustment CommandwOrbiter Pixel Setting Commands Orbiter Time Setting CommandrReal data mapping 1 0 Step Real data mappingPage No picture Troubleshooting check listNo sound No output from oneModel Product specifications