LG Electronics MT-50PZ40, MT-50PZ41, MT-50PZ43S, MZ-50PZ42, MZ-50PZ43 owner manual Screen Position

Page 20

Screen Position

-This function works in the following mode: RGB1-PC or COMPONENT 480p,720p,1080i.

1.Press the MENU button and then D / E button to select the SCREEN menu.

2.Press the G button and then D / E button to select Position.

3.Press the G button and then D / E or F / G button to adjust the position.

4.Press the MENU button.

VIDEO

AUDIO

TIME

SPECIAL

SCREEN

TWIN

Auto configure

ARC

Zoom In/Out

Position G

Manual config.

Screen adj.

Reset

MENU Prev.

¡ª

¢‚ ¢”

¡

Manual Configure (RGB1[PC] mode only)

-If the picture isn’t clear after auto adjustment and especially that characters are still trembling, adjust the picture phase manually.

-To correct the screen size, adjust Clock.

1.Press the MENU button and then D / E button to select the SCREEN menu.

2.Press the G button and then D / E button to select Manual config..

3.Press the G button and then D / E button to to select Phase or Clock.

4.Press the F / G button to make appropriate adjustments.

The adjustment range of Phase is 0 ~ 31.

The adjustment range of Clock is -50 ~ +50.

VIDEO

AUDIO

TIME

SPECIAL

SCREEN

TWIN

Auto configure

ARC

Zoom In/Out

Position

Manual config. G

Screen adj.

Reset

MENU Prev.

Phase Clock

0

0

5.Press the MENU button.

Screen Adjustments (VIDEO (AV1 or AV2), S-VIDEO and COMPONENT 480i mode only)

- This is the function to correct trembling or picture instability while viewing a video tape.

1.Press the MENU button and then D / E button to select the SCREEN menu.

2.Press the G button and then D / E button to select Screen adj..

3.Press the G button and then D / E button to to select TV or VCR.

Select the VCR option if watching a VCR.

Select the TV option for other equipment.(Except VCR)

4.Press the MENU button.

VIDEO

AUDIO

TIME

SPECIAL

SCREEN

TWIN

Auto configure.

ARC

Zoom In/Out

Position

Manual config.

Screen adj.

G

Reset

MENU Prev.

TV

VCR

Initializing (Reset to factory value)

This function operates in every mode.

To initialize the adjusted value

1.Press the MENU button and then D / E button to select the SCREEN menu.

2.Press the G button and then D / E button to select Reset.

3.Press the G button.

• You can initialize ZOOM In/Out, Position, SPLIT ZOOM, PIP size, PIP posi- tion and sub picture size of twin picture.

VIDEO

AUDIO

TIME

SPECIAL

SCREEN

TWIN

Auto configure.

ARC

Zoom In/Out

Position

Manual config.

Screen adj.

ResetG

MENU Prev.

To Set

20

Image 20
Contents Plasma Monitor LG Plasma Monitor Contents Safety Instructions Do not use water the Monitor while cleaningEarth wire should be connected Do not insert any object into the exhaust ventOnly use the specified batteries Do not pull the cord but the plug when unpluggingObjects like a heater Back Panel Controls of the MonitorFront Panel Controls Watching External Equipments Back Panel RCA TypeScart Type External Speaker 8 ohm outputWatching VCR When the Interface board is installed Watching Cable TV When the Interface board is installedWatching DVD When the Interface board is installed How to connectPC Setup Connecting PCSetup Instructions to Connect a PC to your Monitor Displayable Monitor Specification RGB1 mode Resolution Horizontal VerticalResolution Horizontal Vertical RGB2 mode Resolution Horizontal VerticalControls of the remote control Installing BatteriesAccessories Optional ExtrasTo install as desktop type Monitor InstallationTo install as wall mounting type Menu language setup Turning on the Monitor just after installationTurning on the Monitor power cord is still connected Adjusting volume levelAdjusting Auto Colour Control Manual Colour Temperature ControlUser optionVideo Menu PSM Picture Status MemoryAVL Auto Volume Leveler Adjusting Sound Manual SettingPress the SSM button to select the picture appearance setup Audio MenuSetting the Clock Setting the On/Off TimerSleep Timer Time MenuSpecial Menu Child lockOrbiter White WashAuto adjustment RGB1PC mode only Setting Picture FormatScreen Menu Split ZoomScreen Position Manual Configure RGB1PC mode onlyInitializing Reset to factory value PIP Function Sub Picture Size Adjustment Twin PictureSelecting a source for the Twin picture Swapping the Twin PictureExternal Control Device Setup Type of connector D-Sub 9-pin maleRS-232C configurations Set IDCommand Reference List Power CommandaInput select Commandb Main picture input Transmission / Receiving ProtocolAspect Ratio Commandc Main picture format Screen mute CommanddVolume mute Commande Volume control CommandfSharpness Commandk PIP Size CommandoOSD select Commandl Remote control lock mode CommandmBalance Commandt Colour temperature CommanduRed Adjustment Commandv Green Adjustment CommandwOrbiter Time Setting Commandr Orbiter Pixel Setting CommandsReal data mapping 1 0 Step Real data mappingPage Troubleshooting check list No pictureNo sound No output from oneProduct specifications Model