Onkyo HT-R690 Powered Zone, Subwoofer, Front, Center*1, Surround*1, Surround Back*2*3*4*5

Page 42
■Powered Zone 2

Speaker Settings

If you change these settings, you must run Audyssey 2EQ® Room Correction and Speaker Setup again (page 28).

Powered Zone 2

`No

`Yes:

Zone 2 speakers can be used. (Powered Zone 2 enabled).

Note

Before you change this setting, turn down the volume.

When the “Powered Zone 2” setting is set to “Yes”, the surround back or front high speakers cannot be used.

Speaker Configuration

With these settings, you can specify which speakers are connected and a crossover frequency for each speaker. Specify “Full Band” for speakers that can output low frequency bass sounds adequately, for example, speakers with a good sized woofer. For smaller speakers, specify a crossover frequency. Sounds below the crossover frequency will be output by the subwoofer instead of the speaker. Refer to your speaker’s manuals to determine the optimum crossover frequencies.

Note

These settings are not available in either of the following cases:

a pair of headphones is connected.

the “Audio TV Out” setting is set to “On” (page 52).

HDMI Control (RIHD)” is set to “On” (page 51) and you’re listening through your TV speakers.

Subwoofer

`Yes

`No

Front

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

Note

If the “Subwoofer” setting is set to “No”, the “Front” setting is fixed to “Full Band”.

Center*1, Surround*1, Surround Back*2*3*4*5

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None

Front High*1*2*4*6

`Full Band

`40Hz to 100Hz, 120Hz, 150Hz, 200Hz

`None

Note

*1

Full Band” can be selected only when “Full Band” is

 

selected in the “Front” setting.

*2

If the “Surround” setting is set to “None”, this setting cannot

 

be selected.

*3

If the “Surround” setting is set to anything other than “Full

 

Band”, “Full Band” cannot be selected here.

*4

If the “Powered Zone 2” setting is set to “Yes”, this setting

 

cannot be selected.

*5

If anything else than “None” is selected in “Front High”, this

 

setting is automatically set to “None”.

*6

If anything else than “None” is selected in “Surround Back”,

 

this setting is automatically set to “None”.

Surround Back Ch

`1ch:

Select if only one surround back speaker L is connected.

`2ch:

Select if two (left and right) surround back speakers are connected.

Note

If the “Surround Back” Setting is set to “None”, this setting cannot be selected.

LPF of LFE

(Low-Pass Filter for the LFE Channel)

`80Hz, 90Hz, 100Hz, 120Hz

`Bypass:

Low-Pass Filter is not applied.

With this setting, you can specify the cutoff frequency of the LFE channel’s low-pass filter (LPF), which can be used to filter out unwanted hum. The LPF only applies to sources that use the LFE channel.

En

42

Image 42
Contents Instruction Manual ContentsHT-R690 AV ReceiverAVIS Important Safety InstructionsFor Canadian Models PrecautionsFor U.S. models Modèle pour les CanadienSupplied Accessories Installing the batteriesAiming the remote controller Appendix ContentsTurning On & Basic Operations 8ON/STANDBY pageProcessing FeaturesAmplifier Connectionsf g h i j k l Front & Rear Panelsb c d e n o pe f g Displaya b c d jk l mnRear Panel a b cdklmn iuREMOTE CONTROL jackControlling the AV Receiver Remote Controllerd c a dj k a8RECEIVER buttonScrew-typespeaker terminals Connecting the AV ReceiverConnecting Your Speakers Push-typespeaker terminalsSpeaker Configuration Connecting the Speaker CablesSpeaker Connection Precautions Using a Powered Subwoofer Powered subwoofer Corner position1/3 of wall position About AV Connections Connecting AV componentsAV Cables and Jacks Connecting Components with HDMI Audio Return Channel ARC function–“Audio Return Channel” is set to “Auto” page Connecting Your Components A B C D E F G HHow to record a video source System On/Auto Power On Connecting Onkyo uComponentsConnecting a Recording Component Remote Control1 Plug the power cord into an AC wall outlet Connecting the AntennasConnecting the Power Cord Assembling the AM loop antennaTurning On/Off the AV Receiver Turning OnTurning Off h i aj b k cl dm e n f o gp q Controlling Contents of USB or Network DevicesPlayback Playing the Connected ComponentjMENU Understanding Icons on the DisplayPlaying an iPod/iPhone via USB kRETURNExtended Mode Music control Playing a USB DeviceListening to Internet Radio Extended Mode Video controlENTER Listening to Other Internet RadioRegistering My Favorites*1 Top menu of Internet RadioWindows Media Player 11 Setup Playing Music Files on a ServerRemote Playback Windows Media Player 12 SetupUsing the Tuner Listening to AM/FM RadioUsing Remote Playback Tuning into Radio StationsSelecting Presets Presetting AM/FM StationsTuning into stations by frequency Deleting PresetsUsing Basic Functions Using the Automatic Speaker SetupENTER 3 4 5 6 7When you’ve finished making the settings, press ENTERUsing a Powered Subwoofer Error MessagesChanging the Speaker Setup Manually `CancelMOVIE/TV button Using the Listening ModesListening Mode Buttons GAME buttonExplanatory Notes About Listening Modesf b e a pagereverberation of a large hall Onkyo-OriginalDSP Listening ModesListening Modes concert• Dolby PLIIx Game • Dolby PLIIx Movie• Dolby PLIIx Music • Dolby PLIIx MovieInput Listening ModeDescription SpeakerSetting the Display Brightness Using the Home MenuUsing the Sleep Timer Input*1Changing the Input Display Using the Music OptimizerDisplaying Source Information Muting the AV ReceiverRecording Using Headphones1 2 3 AV RecordingCommon Procedures in Setup Menu Advanced SetupOn-screenSetup Menus c 3. Audio Adjust d 4. Source SetupMonitor Out Input/Output AssignResolution HDMI InputDigital Audio Input Speaker SetupComponent Video Input BD/DVD, VCR/DVR, CBL/SAT, GAME, AUX, TV/CD, PORTFront Powered ZoneSubwoofer Center*1, Surround*1, Surround Back*2*3*4*5Double Bass Speaker DistanceLevel Calibration UnitMultiplex Input Channel Audio AdjustDimension Mono Input ChannelListening Angle Source SetupNeo:6 Music Center Image AudysseyReference Level Dynamic VolumeAbout Audyssey Dynamic Volume Audyssey Dynamic EQ Reference Level Offset `0dBENTER IntelliVolumeA/V Sync pageGame Mode*3*4*5 Wide Mode*1*2Picture Mode*1 Film Mode*3*5Audio Selector Audio SelectorCharge Mode Fixed ModeMaximum Volume Listening Mode PresetMiscellaneous Power On VolumeRemote ID Hardware SetupChanging the remote controller’s ID AM/FM Frequency StepAudio Return Channel HDMI ThroughAudio TV Out Lip SyncIP Address MAC AddressDHCP Subnet MaskUsing the Audio Settings Remote Controller SetupLock Setup SetupCinemaFILTER Late NightMusic Optimizer Late NightZone Making Zone 2 ConnectionsOperating on the remote controller Controlling Zone 2 ComponentsOperating on the remote controller Operating on the remote controllerAuto Power On Using the Onkyo DockiPod/iPhone Playback via Onkyo Dock Using the AV receiver’s Remote ControllerOther Remote Controllers Controlling Your iPod/iPhoneAuto Power On iPod/iPhone AlarmPage Entering Remote Control Codes Preprogrammed Remote Control CodesLooking up for Remote Control Code Controlling Other ComponentsResetting the Remote Controller Remote Control Codes for OnkyoResetting REMOTE MODE Buttons Components Connected via uPage Audio TroubleshootingPower Can’t turn on the AV receiverAbout DTS signals There’s no sound with a certain signal formatThe speaker volume cannot be set as required Only the front speakers produce soundTuner Remote ControllerVideo The remote controller doesn’t workZone UP-A1Dock for iPod/iPhoneRecording Music Server and Internet RadioCan’t access the music files on a USB device USB Device PlaybackOthers Standby power consumptionImportant Note Regarding Video Playback COMPONENT VIDEO OUTpage Network Requirements Network/USB FeaturesConnecting to the Network Internet Access for Internet radioServer playback Server RequirementsUSB Device Requirements Remote playbackMP3 .mp3 or .MP3 Supported Audio File FormatsAbout DLNA WMA .wma or .WMAUpdate procedure Firmware UpdateUpdating the Firmware via Network Update via networkUpdate procedure Updating the Firmware via USBTroubleshooting Errors during an update via network8 9 10 11 12 13 Errors during an update via USBConnection Tips and Video Signal Path Video Connection FormatsSignal Selection Audio Connection Formats About HDMI Supported Audio FormatsAbout Copyright Protection Operations that can be performed with pconnection Using an RIHD-compatibleTV, Player, or RecorderAbout p-compatiblecomponents Players/Recorders3 Confirm the settings How to connect and setup1 Confirm the connecting and setting 4 Operate with the remote controllerVideo Inputs SpecificationsHDMI Video OutputsVideo Resolution Chart Available resolutions: 3840 ⋅ 2160 24/25/30 HzOutput Memo 2 9 4 0 0 6 5 Liegnitzerstrasse 6, 82194 Groebenzell, GERMANY