Mitsubishi Electronics XL2550U user manual Projecting images

Page 19

Viewing video images (continued)

C. Projecting images

Preparation:

Remove the lens cap.

Turn on the power of the connected video equipment.

FOCUS ring

ZOOM ring

COMPUTER button

POWER button

POWER button COMPUTER1, 2 buttons

DVI-D (HDCP) button S-VIDEO button VIDEO button

VIDEO button

1.Confirm the POWER indicator lights up red.

If the projector was turned off before the lamp was cooled down sufficiently last time, the fan may start rotating and the POWER button may not work after the power cord is plugged. (The STATUS indicator blinks green.) After the fan stops rotating, press the POWER button to turn back on the POWER indicator.

2.Press the POWER button.

It may take about 1 minute for the lamp to light up.

The lamp fails to light up on rare occasions. In such a case, wait for a few minutes and then try again.

Do not cover the lens with the lens cap while the lamp is on. Do not strip off the aluminium sheet inside the lens cap.

After the POWER button is pressed, the image may flicker before the lamp becomes stable. This is not a prod- uct malfunction.

Regardless of the setting of LAMP MODE in the INSTALLATION menu, the STANDARD lamp mode is activated by default whenever the projector is turned on. When LAMP MODE has been set to LOW, the lamp mode changes from STANDARD to LOW about 1 minute after turn-on.

The projector starts warming up when the POWER button is pressed. During the warm-up process, images may appear dark and no commands are accepted.

By blinking red, the STATUS indicator indicates that the lamp should be replaced soon. Replace the lamp when the STATUS indicator blinks red. (See page 37.)

3.Select an input source.

Press the VIDEO button on the projector or the VIDEO or S-VIDEO button on the remote control that is corresponding to the terminal in use.

The input source is switched between VIDEO and S-VIDEO at every press of the VIDEO button on the projector.

The VIDEO and S-VIDEO buttons don’t function while the menu is being displayed.

Though it may take some time before an image is displayed on the screen depending on the type of the input signal, such symptom is not a malfunction.

Some images become easier to view when the setting of aspect ratio is changed. (See page 21.)

When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO DVI- D(HDCP) terminal, press the COMPUTER button on the projector to select DVI or press the DVI-D (HDCP) button on the remote control.

When projecting images from a DVD player that is connected to the COMPUTER/COMPONENT VIDEO IN-1/ IN-2 terminal, press the COMPUTER button on the projector or the COMPUTER 1 or COMPUTER 2 button on the remote control.

4.Adjust the position of the projector to keep an appropriate projection distance with which images are projected in their specified sizes.

5.Adjust the position of the projector so that the projector and the screen are perpendicular to each other. (See page 10.)

When the projector cannot be positioned perpendicularly to the screen, adjust the projection angle. (See page 10.)

6.Adjust the size of the projected image by turning the ZOOM ring.

7.Adjust the focus by turning the FOCUS ring.

Repeat steps 4 to 7, if necessary.

EN-19

Image 19
Contents XL2550 XL1550 Compliance Notice When using the projector in EuropeContents Important safeguards Important safeguards Inserting the batteries into the remote control Checking accessoriesPreparing your projector Terminal board Preparating your projectorOverview Control areaBottom side Remote controlAbout the laser beam Front of projector Rear of projector Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupRear projection Setting up your projectorWall screen Front projection, ceiling mountingScreen size and projection distance When the aspect ratio of the screen isViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordAbout DDC Projecting images AV mute When connecting to a notebook computerExample of the setting procedure for external output To stop projectingViewing video images Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connectedProjector + DVD player or Hdtv decoder Plugging in the power cordConnecting to video equipment having a DVI-D terminal Viewing video imagesProjecting images Volume from the speaker How to change the settings Setting the aspect ratioWhen projected images are distorted to a trapezoid Menu operation SetupAvailable settings in the menus How to set the menusMenu operation Menu operation EN-25 EN-26 EN-27 To cancel the menu Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureEN-30 LPF Progressive filter To adjust the vertical positionSetting of the image displayed during startup or muting Advanced featuresTo cancel the password function Advanced featuresPassword function To enable the password functionPicture in Picture PinP ExpandStill PageUp button Mouse remote controlProjector + computer with USB connector OperationMajor functions Supervising and controlling by computerConnection Normal condition IndicatorsReplacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector Replacing the lampCleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsNo image appears on the screen TroubleshootingNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxEN-45 COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp ConnectorsMitsubishi Projector Contact Information