Mitsubishi Electronics XL2550U user manual Advanced features

Page 32

Advanced features

Setting of the image displayed during startup or muting

You can display your desired image as the startup screen (or splash screen). Using the menu, you can also use such image as a background that is displayed while the video is muted or no signal is supplied.

Important:

•You can’t set IMAGE CAPTURE when PASSWORD FUNCTION in the FEATURE menu has been set to SPLASH ID SCREEN to enable the password lock.

•You can’t set IMAGE CAPTURE when the compo- nent video signal is inputted.

Setting procedure

1.Press the COMPUTER button to select the image supplied to the COMPUTER/COMPONENT VIDEO IN terminal.

2.Display your desired image.

3.Display the INSTALLATION menu.

4.Select IMAGE CAPTURE by pressing the S or T button.

5.Press the ENTER button.

• The setting menu will be displayed.

opt.

 

INSTALLATION

 

CUSTOM IMAGE CAPTURE

BACK COLOR

GRAY

SIZE

x1

CAPTURE

GO

Set the background color

(Set the background color only when you set the im- age size to x1 or x2.)

6.Select BACK COLOR by pressing the S or T but- ton.

7.Select your desired color for the background (GRAY,

RED, GREEN, BLUE, BLACK, WHITE, RED50%, GREEN50%, or BLUE50%) by pressing the W or X button.

Set the image size

8.Select SIZE by pressing the S or T button.

9.Select x1, x2, or FULL by pressing the W or X but- ton.

x1

x2

FULL

Capture the image

10.Select CAPTURE by pressing the S or T button. 11.Press the ENTER button.

•A red frame appears. (The size of the red frame is 320x240 pixels.)

CAPTURE : ENTER X2

CANCEL : MENU

CAPTURE : ENTER + ENTER

CANCEL : MENU

12.Adjust the size of the image to be captured so that such image stays within the red frame.

•Press the S, T, W or X button to move the red frame.

•You can’t move the red frame outside the screen.

CAPTURE : ENTER X2

CANCEL : MENU

13.Press the ENTER button twice.

•Image capture will start.

•Press the MENU button to cancel the procedure.

CAPTURING IMAGE !

LVP-XD300

•When the image capture completes, the cap- tured image will be displayed for three seconds.

Important:

•You can’t change the new startup screen back to the original startup screen. (Even when you select RESET ALL in the FEATURE menu, the factory default screen isn’t available any longer.) When you want to change the startup screen again, capture another image.

•The captured image will be displayed from the next startup. If the captured image isn’t displayed, make sure that the setting of SPLASH SCREEN in the INSTALLATION menu isn’t OFF. (See page 24.)

•To display the captured image while the video is muted, set MUTE MODE in the INSTALLATION menu to IMAGE. (See page 24.)

•When BACK COLOR in the INSTALLATION menu is set to IMAGE, the captured image will be displayed while no signal is supplied.

•Some images can’t be captured correctly because of their signal type.

EN-32

Page 31 Page 33
Image 32
Page 31 Page 33
Contents XL2550 XL1550 When using the projector in Europe Compliance NoticeContents Important safeguards Important safeguards Preparing your projector Checking accessoriesInserting the batteries into the remote control Preparating your projector OverviewControl area Terminal boardAbout the laser beam Remote controlBottom side Using the remote control Operational range of the remote controlReception angle Front of projector Rear of projectorSetting up your projector Setting up the screenBasic setup Adjusting the projection angleSetting up your projector Wall screenFront projection, ceiling mounting Rear projectionWhen the aspect ratio of the screen is Screen size and projection distanceConnecting the projector to a computer Viewing computer imagesAbout DDC Plugging the power cordViewing computer images Projecting images When connecting to a notebook computer Example of the setting procedure for external outputTo stop projecting AV muteConnecting the projector to video equipment Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesPlugging in the power cord Connecting to video equipment having a DVI-D terminalViewing video images Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker When projected images are distorted to a trapezoid Setting the aspect ratioHow to change the settings Setup Menu operationMenu operation How to set the menusAvailable settings in the menus Menu operation EN-25 EN-26 EN-27 Adjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To cancel the menuAdjusting projected images To adjust the tone of white Color TempAbout color temperature Color EnhancerEN-30 To adjust the vertical position LPF Progressive filterAdvanced features Setting of the image displayed during startup or mutingAdvanced features Password functionTo enable the password function To cancel the password functionStill ExpandPicture in Picture PinP Mouse remote control Projector + computer with USB connectorOperation PageUp buttonConnection Supervising and controlling by computerMajor functions Indicators Normal conditionInterval of lamp replacement Replacing the lampReset of the lamp operation time When removing the lamp from the ceiling-mounted projectorReplacing the lamp To replace the lampMaintenance Cleaning of the air-filterCleaning of the projector and the ventilation slots Cleaning of the lensTroubleshooting No image appears on the screenImages are not displayed correctly Problem Solution TroubleshootingNo image appears on the screen Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsEN-45 Connectors COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D HdcpMitsubishi Projector Contact Information
Top Page Image Contents