Mitsubishi Electronics XL2550U user manual Replacing the lamp, To replace the lamp

Page 39

Replacing the lamp (continued)

To replace the lamp:

(b)1. Unplug the power cord.

2.Loosen the screw (a) using a Phillips screwdriver (+), and remove the lamp cover (b).

3. Loosen the screws (c) using a Phillips screwdriver (+).

4. Pull the handle.

(a)5. Pull out the lamp box by the handle while holding the projector.

 

 

• Pull the lamp box out of the projector slowly. If it is

(c)

 

pulled out quickly, the lamp may break scattering glass

 

fragments.

 

 

• Do not spill liquid on the removed lamp box or do not

 

 

place it near any flammable object or where children

 

 

can reach to prevent injury or fire.

 

6.

Load a new lamp box securely into the projector in the right

 

 

orientation.

 

7.

Put the handle back to the original position.

 

 

• Make sure that the handle is locked.

 

8.

Tighten up the screws (c) using a Phillips screwdriver (+).

 

9.

Tighten up the screw (a) using a Phillips screwdriver (+) to

 

(c)

secure the lamp cover.

 

 

 

Reset of the lamp operation time

 

Plug in the power cord and reset the lamp operation time by

 

holding down the W, X, and POWER buttons on the control

(a)

panel at the same time about three seconds.

Important:

Unless these 3 buttons are pressed at the same time, the lamp operation time isn’t reset.

Make sure that the STATUS indicator is lit twice and the lamp operation time is reset successfully.

The projector doesn’t turn on if the lamp cover isn’t attached securely.

Be sure to reset the lamp operation time whenever you replace the lamp.

Do not reset the lamp operation time unless you replace the lamp.

When removing the lamp from the ceiling-mounted projector

When removing the lamp from the ceiling-mounted projector, use the lamp replacement tray packed with the projector or option lamp to prevent glass fragments from scattering.

Assemble the lamp replacement tray according to the procedure shown on it.

1.Follow steps 1 to 4 shown above.

2.Attach the lamp replacement tray to the projector as shown

Tape

Important:

in the figure.

3. Secure the lamp replacement tray on the projector using the tape packed with the tray.

4 Pull out the lamp box by the handle while holding the projector.

• Hold the lamp replacement tray to prevent glass fragments from scattering.

• Don’t put the lamp directly on the lamp replacement tray because it may fall.

5.Detach the lamp replacement tray together with the removed lamp.

The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For the U.S. only.)

EN-39

Image 39
Contents XL2550 XL1550 Compliance Notice When using the projector in EuropeContents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Terminal board Preparating your projectorOverview Control areaRemote control Bottom sideAbout the laser beam Front of projector Rear of projector Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupRear projection Setting up your projectorWall screen Front projection, ceiling mountingScreen size and projection distance When the aspect ratio of the screen isViewing computer images Connecting the projector to a computerPlugging the power cord Viewing computer imagesAbout DDC Projecting images AV mute When connecting to a notebook computerExample of the setting procedure for external output To stop projectingViewing video images Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connectedProjector + DVD player or Hdtv decoder Plugging in the power cordConnecting to video equipment having a DVI-D terminal Viewing video imagesProjecting images Volume from the speaker Setting the aspect ratio How to change the settingsWhen projected images are distorted to a trapezoid Menu operation SetupHow to set the menus Available settings in the menusMenu operation Menu operation EN-25 EN-26 EN-27 To cancel the menu Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureEN-30 LPF Progressive filter To adjust the vertical positionSetting of the image displayed during startup or muting Advanced featuresTo cancel the password function Advanced featuresPassword function To enable the password functionExpand Picture in Picture PinPStill PageUp button Mouse remote controlProjector + computer with USB connector OperationSupervising and controlling by computer Major functionsConnection Normal condition IndicatorsReplacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector Replacing the lampCleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsNo image appears on the screen TroubleshootingTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxEN-45 COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp ConnectorsMitsubishi Projector Contact Information