Mitsubishi Electronics XL2550U user manual To adjust the vertical position, LPF Progressive filter

Page 31

Adjusting projected images (continued)

How to adjust the image supplied from the computer using the menu:

Carry out the following procedures according to the symptoms.

Wide strips appear. ……………………………………… Adjust TRACKING in the SIGNAL menu.

The projected image flickers.

 

 

 

The projected image is blurred

Adjust FINE SYNC. in the SIGNAL menu.

The projected image is displaced horizontally

Adjust HORIZ.POSITION in the SIGNAL menu. Every time the

 

W button is pressed, the image moves to the right. Every time

 

the X button is pressed, the image moves to the left.

The projected image is displaced vertically

Adjust VERT.POSITION in the SIGNAL menu. Every time the W

 

button is pressed, the image moves down. Every time the X

 

button is pressed, the image moves up.

The top part of the image flags

Change the setting of HOLD in the SIGNAL menu. Select ON

 

,

 

 

press the ENTER button, and adjust BEGIN or END to minimize

 

the flagging.

A solid black or solid white appears in the image

Adjust CLAMP POSITION or CLAMP WIDTH in the SIGNAL -

 

USER menu.

The motion doesn’t run smoothly

Adjust VERT. SYNC in the SIGNAL - USER menu. Select

 

AUTO for normal use.

Noise appears on the right or left half of the image

Adjust SHUTTER(LS) or SHUTTER(RS) in the SIGNAL - USER

 

menu.

Noise appears on the top or bottom part of the image

Adjust SHUTTER(U) or SHUTTER(L) in the SIGNAL - USER

 

menu.

1.Display the SIGNALmenu.

2.Press the S or T button to select an item to adjust.

3.Adjust the selected item by pressing the W or X button.

To cancel the menu:

4. Press the MENU button.

• Do not change the settings of the SIGNAL menu in normal use.

Simple method to adjust the image position

To adjust the horizontal position:

1.Align the left edge of the image with the left side of the screen by adjusting HORIZ.POSITION. Then, align the right edge of the image with the right side of the screen by adjusting TRACKING.

2.Repeat step 1 above to complete the adjustment of the horizontal position.

To adjust the vertical position:

3. Align the upper edge of the image with the upper side of the screen by adjusting VERT.POSITION.

LPF (Progressive filter)

You can select whether or not to enable the LPF.

Vertical or horizontal streak noise may appear on the projected image, depending on the type of the DVD player or game console you use. In such a case, you can reduce such streak noise by enabling the LPF. However, projected images become softened slightly.

EN-31

Image 31
Contents XL2550 XL1550 Compliance Notice When using the projector in EuropeContents Important safeguards Important safeguards Inserting the batteries into the remote control Checking accessoriesPreparing your projector Terminal board Preparating your projectorOverview Control areaBottom side Remote controlAbout the laser beam Front of projector Rear of projector Using the remote controlOperational range of the remote control Reception angleAdjusting the projection angle Setting up your projectorSetting up the screen Basic setupRear projection Setting up your projectorWall screen Front projection, ceiling mountingScreen size and projection distance When the aspect ratio of the screen isViewing computer images Connecting the projector to a computerViewing computer images Plugging the power cordAbout DDC Projecting images AV mute When connecting to a notebook computerExample of the setting procedure for external output To stop projectingViewing video images Connecting the projector to video equipmentConnecting to a video player, etc When a TV tuner or VCR is connectedProjector + DVD player or Hdtv decoder Plugging in the power cordConnecting to video equipment having a DVI-D terminal Viewing video imagesProjecting images Volume from the speaker How to change the settings Setting the aspect ratioWhen projected images are distorted to a trapezoid Menu operation SetupAvailable settings in the menus How to set the menusMenu operation Menu operation EN-25 EN-26 EN-27 To cancel the menu Adjusting projected imagesTo adjust the brightness Contrast and Brightness To adjust the color Color and TintColor Enhancer Adjusting projected imagesTo adjust the tone of white Color Temp About color temperatureEN-30 LPF Progressive filter To adjust the vertical positionSetting of the image displayed during startup or muting Advanced featuresTo cancel the password function Advanced featuresPassword function To enable the password functionPicture in Picture PinP ExpandStill PageUp button Mouse remote controlProjector + computer with USB connector OperationMajor functions Supervising and controlling by computerConnection Normal condition IndicatorsReplacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector Replacing the lampCleaning of the lens MaintenanceCleaning of the air-filter Cleaning of the projector and the ventilation slotsNo image appears on the screen TroubleshootingNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution Kensington Lock Others Problem SolutionSpecifications Replacement part option/not included in the boxEN-45 COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D Hdcp ConnectorsMitsubishi Projector Contact Information