Mitsubishi Electronics XL2550U user manual Preparing your projector, Checking accessories

Page 6

Preparing your projector

Checking accessories

The following accessories are provided with this projector. Check to be sure that all of the accessories are packed in the package.

Cables

 

 

Mini D-SUB

D-SUB

 

USB 4-pin

15-pin

 

9-pin

 

(type B)

 

 

 

 

 

 

Mini D-SUB

D-SUB

 

USB 4-pin

15-pin

 

(type A)

 

9-pin

Audio/Video cable

USB cable

RGB cable for PC

RS-232C cable

(246C381-10)

(246C509-10)

(246C521-10)

(246C548-10)

• Used for projector control by computer.

Power supply parts

Power cord (two)

(246C483-10, 246C383-20)

Remote control parts

Remote control

R6P (size-AA)

(290P136-10)

battery (two)

Others

•Lens cap (Attached to the projector)

•Lamp replacement tray ( 857C106-10)

•CD-ROM (919C154-60)

•Safety Manual/

Quick Start up (871D489-60)

Important:

• The attached power cords are to be used exclusively for this product. Never use them for other products.

Inserting the batteries into the remote control

1

1.

Remove the rear lid of the remote control.

2.

Check the polarity (+), (-) of the batteries, and set them

 

3

correctly, inserting their (-) side first.

•If the battery is inserted from the (+) side first, inserting the (-) side is difficult because the coil spring end hits on the battery side. If the battery is forced to insert in this

2

way, the outer label of the battery may get ripped and it

may cause a short-circuit and heating.

 

 

3. Attach the rear lid.

Important:

• Use two size-AA batteries (R6P).

• Replace the 2 batteries with new ones when the remote control is slow to operate.

Caution:

•Use of a battery of wrong type may cause explosion.

•Only Carbon-Zinc or Alkaline-Manganese Dioxide type batteries should be used.

•Dispose of used batteries according to your local regulations.

•Batteries may explode if misused. Do not recharge, disassemble, or dispose of them in fire.

•Be sure to handle the batteries according to the instructions.

•Load the batteries with its positive (+) and negative (-) sides correctly oriented as indicated on the remote control.

•Keep batteries out of reach of children and pets.

•Remove the batteries, if the remote control is not used for a long time.

•Do not combine a new battery with an old one.

•If the solution of batteries comes in contact with your skin or clothes, rinse with water. If the solution comes in contact with your eyes, rinse them with water and then consult your doctor.

EN-6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents XL2550 XL1550 When using the projector in Europe Compliance Notice Contents Important safeguards Important safeguards Checking accessories Inserting the batteries into the remote controlPreparing your projector Control area Preparating your projectorOverview Terminal boardRemote control Bottom sideAbout the laser beam Reception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleFront projection, ceiling mounting Setting up your projectorWall screen Rear projectionWhen the aspect ratio of the screen is Screen size and projection distanceConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesAbout DDC Projecting images To stop projecting When connecting to a notebook computerExample of the setting procedure for external output AV muteWhen a TV tuner or VCR is connected Connecting the projector to video equipmentConnecting to a video player, etc Viewing video imagesViewing video images Plugging in the power cordConnecting to video equipment having a DVI-D terminal Projector + DVD player or Hdtv decoderProjecting images Volume from the speaker Setting the aspect ratio How to change the settingsWhen projected images are distorted to a trapezoid Setup Menu operationHow to set the menus Available settings in the menusMenu operation Menu operation EN-25 EN-26 EN-27 To adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To cancel the menuAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp Color EnhancerEN-30 To adjust the vertical position LPF Progressive filterAdvanced features Setting of the image displayed during startup or mutingTo enable the password function Advanced featuresPassword function To cancel the password functionExpand Picture in Picture PinPStill Operation Mouse remote controlProjector + computer with USB connector PageUp buttonSupervising and controlling by computer Major functionsConnection Indicators Normal conditionInterval of lamp replacement Replacing the lampReplacing the lamp Reset of the lamp operation timeWhen removing the lamp from the ceiling-mounted projector To replace the lampCleaning of the projector and the ventilation slots MaintenanceCleaning of the air-filter Cleaning of the lensTroubleshooting No image appears on the screenTroubleshooting No image appears on the screen Problem SolutionImages are not displayed correctly Problem Solution Others Problem Solution Kensington LockReplacement part option/not included in the box SpecificationsEN-45 Connectors COMPUTER/COMPONENT Video IN-1/IN-2 DVI-D HdcpMitsubishi Projector Contact Information
Top Page Image Contents