Mitsubishi Electronics XD50U user manual Startup Logo Creation, Start Capture → Page E-50

Page 59

Startup Logo Creation

7.Start Capture → Page E-50

Selection will not be possible unless a signal is being input. Pressing the ENTER button will start the capture.

(1)While capture is operating, “Capturing Logo” is displayed and the advance- ment of the gauge is displayed.

(2)When the capture is completed, “Logo Capture Complete” is displayed for about 10 seconds.

(3)When a logo capture has already been saved, it will be overwritten.

•When capture was not possible due to the logo size being too large, “Not Enough Space. Over Memory Limit ***%” is displayed. (*** repre- sents a numerical value.)

Change the capture size using the percentage exceeded as a guide, or change the capture mode and start capture again.

•When a mistake has been made in logo capture, the message “Logo Capture Failed” is displayed.

Please try it again.

8.Check the logo Capture Screen at Startup Time → Page E-50 Select “Preview” and press the ENTER button.

To close, press the ENTER button or the CANCEL button. There is a re- turn to the menu display.

This completes the startup logo.

The next time the projector is started, the captured logo will be displayed.

Note:

*This function is for the logo. Full-color photographs with many colors that fill the projection screen cannot be captured. Please make such photographs into a small size.

*Capture ranges that exceed the output resolution of the projector cannot be se- lected.

*The area outside the red lines of the red frame becomes the selection range for the capture range selection.

*To match the background color of the startup logo with the background color of the created image, examine the values (i.e., 0 to 255) of the RGB colors of the created image using image software and set the various values to the custom RGB of the logo background color.

*Pressing the STANDBY button during the capture will not switch off the power. This is to prevent the loss of the capture data during the capture (by switching off the power). To switch off the power, please press the STANDBY button after the capture is completed.

*When a mistake has occurred with the capture, the logo that was previously captured will also be deleted.

Capturing Logo

E-58

Page 58 Page 60
Image 59
Page 58 Page 60
Contents XD50 Important Safety Information Important Safety Information If you break or drop the cabinet Place of installationNever remove the cabinet Do not modify this equipmentMajor Features Table of Contents Table of Contents Checking the Supplied Accessories Carrying case for projector and accessories Checking the Supplied AccessoriesNames of the Main Unit Parts Names of the Main Unit Parts Built-in Security SlotStandby button E-21 Names of the Remote Control PartsVOL button E-30 Volume adjustment display Infrared transmitter E-12Using the remote control for the first time Preparing the Remote ControlButton Battery Replacement Remote Control RangeProcedure Up to Projecting to the Screen Screen Size and Projection Distance Placement GuideDVI-D cable Not supplied Personal Computers with a DVI ConnectorConnections with Personal Computer DVI/mini D-Sub 15-pin conversion cable Supplied item Personal Computers with a Mini D-Sub 15-Pin ConnectorConnecting Personal Computers and Video Equipment Personal computerManufacturer Model Key To Output the External Output Signal of a Notebook Computer→ Video See Input Format on Page E-47 Connections with Composite SignalsVideo Equipment with Video Connectors Video Equipment with S-VIDEO ConnectorsGreen Blue Red Connections with Component SignalsGreen Blue Red Cb Cr Pb PrSupplied item Connections with the Audio JackAudio cable Supplied item Audio conversion cableFirmly plug in all the way To wall outlet Switch on the projector powerOperating Lit amberCursor Power Cable Connections and Switching the Power On/OffPress the Enter button to set This completes the selection of the display languageFinishing Unplug the power cableStandby indicator changes to flash Standby modeZoom ring Adjustment of the Projection ScreenAdjustment of the Projection Screen Adjust the projection image to the screenLowering the projection image Making Adjustments with the AdjustersFocus ring Raising the projection imageGeneral Operation Automatic AdjustmentWhen Auto Source is On When Auto Source is OffGeneral Operation Video Signals / Component SignalsSelection of Aspect Ratio Freezing a Moving Picture Cancelling Video and Audio TemporarilyLamp Mode Using the Presentation Timer Keystone Adjustment of the VolumeAdjust the volume To close the display immediately, press the Cancel buttonEnlarge to the desired size Enlargement of the Image and Video MovementImage can also be moved in the following circumstances Press the Zoom buttonVolume Using the Quick MenuContent of Adjustments and Settings Example Brightness adjustment displayMain unit buttons Menu Operation MethodMenu Name Adjustment Bar Item NameMenu Screen Names and Functions Menu Operation MethodMenu Display Press the Menu button to display the menu Performing Menu OperationsThis condition al- lows selection of the item name Making Adjustments/SettingsSelecting Another Menu Name with Remote Control Operation Imput ColorView Info Menu name Item Name Sub Menu SetupPicture Adj. / Fine Picture / H Position / V Position Picture Adj. Picture AdjustmentPicture Brightness / Contrast / Color / Tint / SharpnessPosition ResetPress of the Enter button forces the reset Fine PictureWhite ColorGamma Color TempWhite Balance Selection contents at the time of YCbCr inputSelection contents at the time of YPbPr input Color SpaceFilter Video SignalsView AspectView Power cable has been unpluggedVertical Flip Keystone SaveMenu Position SetupAuto Power Off Auto SourceVideo and SVideo SetupInput Format Logo Scaling Presentation TimerTo start the timer Logo BackgroundInvalidata Logo Capture ModeLogo Position Preview Start Logo CaptureFolder Initial SettingPlay Mode Switches the slide manuallyProgress Bar During Thumbnail Display IntervalRepeat Progress BarBackground Example of a display when Aspect button is pressedLanguage On ScreenDisplays the logo Startup ScreenStatus Factory DefaultLamp Timer Reset InfoInfo Resolution / FrequencyLamp Timer Preparation and Projection of the Image Logo Capture SettingsStartup Logo Creation Start Capture → Page E-50 Startup Logo CreationTerminology Used in the Viewer Using the PC Card ViewerBefore Using the PC Card Viewer Store the images on a CompactFlash Card Using the PC Card ViewerSlide Creation Method  Slide Creation GuideSource button Names and Functions of the Viewer FunctionsPC-CARD button Slide  Using the Tool Bar Names and Functions of the Viewer Screen Parts  Removal from the PC Card Slot Using CompactFlash CardsInsertion to the PC Card Slot of the Personal Computer  Insertion to the PC Card SlotSet to PC-CARD Switch the Input to the PC CardWhen PC Card Error is displayed PC Card Viewer OperationSelection Method When a folder has been selected and opened,When the Select button has been pressed Rotation of the Slides Thumbnail Display and Settings ChangesWhen the File Open Error is Displayed View the SlidesThermal Protector When an Indicator is Lit or FlashingCheck the following matters before requesting servicing TroubleshootingDirty Lens CleaningCleaning a Soiled Projector Main Unit Cleaning the Inside of the ProjectorReplacing the Lamp Cartridge Remove the lamp cartridge Replacing the Lamp CartridgeMount the lamp cover Reset the Lamp TimerMount the new lamp cartridge Mechanical SpecificationsOptical ElectricalTable of Supported Frequency SignalResolution Frequency Video Digital Analog 239 190 Unit mm inch Cabinet DimensionsMitsubishi Electric Corporation

XD50U specifications

The Mitsubishi Electronics XD50U is a compact and versatile LCD projector designed to deliver high-quality images and excellent performance for a variety of applications. Ideal for both business presentations and educational purposes, the XD50U offers a blend of advanced features, reliability, and ease of use, making it a popular choice among professionals and educators alike.

One of the standout features of the XC50U is its bright 5000 ANSI lumens output, ensuring clear and vivid images even in well-lit environments. Coupled with a native XGA resolution of 1024 x 768 pixels, this projector provides sharp and detailed visuals, making it suitable for intricate presentations, graphs, and videos.

The projector boasts a high contrast ratio of 2000:1, which enhances color depth and detail. This feature is particularly beneficial when presenting images or videos that require clear visual differentiation. The XD50U also supports a range of input formats, including HDMI, VGA, and composite video, ensuring compatibility with a wide array of devices such as laptops, DVD players, and gaming consoles.

Another significant attribute of the Mitsubishi XD50U is its user-friendly design. Weighing just under 6 pounds, this projector is lightweight and portable, allowing for easy transportation between rooms or venues. The intuitive control panel and remote control simplify operation, making it accessible for users with varying levels of technical expertise.

In terms of longevity and maintenance, the XD50U is equipped with a long-lasting lamp that can achieve up to 3000 hours of runtime in standard mode and extend to 4000 hours in eco mode. This extended lifespan reduces the frequency of lamp replacements, providing a cost-effective solution for users.

For additional convenience, the XD50U includes features such as automatic vertical keystone correction, which ensures that images are presented without distortion, and a quick start function that minimizes setup time. The built-in speaker also enhances presentations by providing audio without the need for external sound equipment.

Overall, the Mitsubishi Electronics XD50U is a powerful, feature-rich projector that caters to diverse presentation needs, offering reliable performance, vibrant image quality, and practical usability. Whether used in classrooms or conference rooms, the XD50U remains a solid choice for anyone in need of a dependable presentation solution.
Top Page Image Contents