Mitsubishi Electronics XD470U/XD470U-G Power-off, Instant Shut Down, Auto Position button

Page 14

Basic operation (continued)

Power-off

Use the following procedure to turn off the projector.

1.Press the POWER button on the control panel or the OFF button on the remote control.

•The message "POWER OFF? YES : PRESS AGAIN" appears on the screen.

•To cancel, press any button except the POWER button. (Some buttons on the remote control don’t function for can- cel.)

2.Press the POWER button on the control panel or the OFF button on the remote control within 10 seconds again.

•The lamp will go out and the STATUS indicator will start blinking.

•Though the lamp goes out at this second press of the POWER button (or OFF button), the air outlet fans continue operating for one minute to cool down the lamp. The STA- TUS indicator will stop blinking.

•After stopping the air outlet fans, if the temperature inside the set is still high, the temperature sensor detects it and then the air outlet fans may start again.

3.Unplug the power cord.

•The POWER indicator will go out.

•If the power cord should be unplugged accidentally while either the air inlet fan or the air outlet fans are operating or the lamp is on, allow the projector to cool down for 10 min- utes with the power off. To light the lamp again, press the POWER button (or OFF button). If the lamp doesn’t light up immediately, repeat pressing the POWER button (or OFF button) two or three times. If it should still fail to light up, replace the lamp.

Notice:

•When storing the projector in the carrying case, the lens should face up.

Instant Shut Down

You can turn off this projector just by unplugging the power cord with- out pressing the POWER button.

•Don't shut down the projector while the STATUS indicator is blink- ing after the lamp lights up because the lamp's life may be short- ened.

•Don't turn the projector back on right after shutting it down because the lamp's life may be shortened. (Wait about 10 minutes before turning the projector back on.)

•Before shutting down the projector, be sure to close the menu screen. If you shut down the projector without closing the menu, the setting data of the menu may not be saved.

AUTO POSITION button

When the image isn’t projected in the right position with COMPUTER selected as the input source, follow the procedure below.

1.Project a bright image such as the "Recycle Bin" window on the full screen.

2.If the screen saver is running, turn it off.

3.Press the AUTO POSITION button.

•If the image is still not in the right position, adjust the image position using the SIGNAL menu. See page 19.

Volume from the speaker

Press the VOLUME + or -button to change the volume from the speaker.

The volume control bar will appear on the screen.

VOLUME

10

•The volume control bar will disappear about 10 seconds after the VOLUME button is released.

•The VOLUME buttons don’t function while the menu selection bar or the menu is being displayed.

•When a high-level audio signal, such as a DVD audio signal, is supplied to the AUDIO IN terminal, the output from the speaker may be distorted.

AV mute

The video and audio signals are temporarily muted when the MUTE button is pressed. To cancel muting, press the MUTE button again.

ANAMORPHIC mode

When playing DVD discs containing data of letterboxed image, press the 16:9 button. Exit the ANAMORPHIC mode, by pressing the 16:9 button again.

Important:

•When a letterboxed image is kept displayed for a long time before displaying 4:3 image, the afterimages of the black bars may appear on the 4:3 image screen. Consult your dealer in this case.

Caution:

•After using the projector, wait one minute for the air outlet fans to stop. Then unplug the power cord from the wall outlet.

•The lamp can’t be lit again for one minute after turned off for safety purpose. It will take another one minute for the STATUS indicator to go out. If you want to turn on the projector again, wait until the indicator goes out, and then press the POWER button.

•The air outlet fans rotate faster as the temperature around the pro- jector rises.

•When the temperature around the projector rises high, the sign "TEMPERATURE!!" blinks red on the screen. If the temperature stays high, the lamp will go out automatically.

Important:

•Do not display a still picture for a long time because the afterim- ages may persist on the screen.

EN-14

Page 13 Page 15
Image 14
Page 13 Page 15
Contents XD470U/XD470U-G When using the projector in Europe ShockContents Important safeguards Do not unplug the power cord during operation Do not keep using the damaged projectorDo not look into the lens when the projector is operat- ing Place of installationTerminal board OverviewControl panel Remote control Bottom sideOperation range of the remote control Remote controlBattery installation Reception angle vertical Reception angle horizontalFront projection InstallationLayout of the projector Front projection, ceiling mountingProjector + DVD player or Hdtv decoder Basic connectionsProjector + AV device For analog connection Projector + ComputerFor computer with Mini D-SUB For monitor connectionUsing the adjustment feet rear Adjustment of the projection angleUsing the adjustment feet front PreparationPower-on Basic operationAnamorphic mode Power-offVolume from the speaker Instant Shut DownMenu operation Basic operationMenu operation Feature Signal User No need to adjust in normal useColor temperature Image adjustmentImage adjustment Adjustment of the image from the computer Simple adjustment methodTo resume the motion in the image Advanced featureStill Page-up and page-downTo enable the password function Password functionTo cancel the password function Lamp replacement Interval of lamp replacementTroubleshooting Images aren’t projected on the screenTroubleshooting Images aren’t projected correctlyCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots OthersAbnormal condition IndicatorsNormal condition Specifications Replacement part ConnectorsDimensional drawings unit mm What’s included in the boxSignal mode Resolution Horizontal Vertical Mitsubishi Electric Corporation

XD470U/XD470U-G specifications

The Mitsubishi Electronics XD470U/XD470U-G are advanced digital projectors designed for business and educational environments, providing high-quality images and a range of features that enhance presentations and learning experiences. Notable for their versatility, these projectors can accommodate various applications, making them an ideal choice for conference rooms, classrooms, and auditoriums.

At the heart of the XD470U/XD470U-G is a powerful imaging system that delivers stunningly bright and vivid visuals. With a brightness rating of 4500 ANSI lumens, these projectors ensure clarity even in well-lit rooms. They feature a native resolution of XGA (1024 x 768), which is compatible with a wide range of content types, from text to intricate graphics, ensuring that every detail is clearly visible.

One of the standout technologies in the XD470U/XD470U-G is its advanced Color Management technology which produces exceptional color accuracy. This technology helps in achieving vibrant colors that maintain their integrity across various viewing conditions. Coupled with a contrast ratio of 2000:1, the projectors offer deep blacks and bright whites, enhancing the overall quality of the visual experience.

The XD470U/XD470U-G projectors are equipped with a variety of input options, including HDMI, VGA, and USB, making connectivity seamless and adaptable to different devices. Additionally, the inclusion of RS-232 control allows for easy integration with existing AV systems, providing flexibility for users who require advanced management options.

Portability is another key feature, with a compact design and lightweight build enabling easy transportation between locations. This makes the XD470U/XD470U-G ideal for mobile professionals who often conduct presentations in different venues.

The projectors also boast an extended lamp life of up to 6000 hours in eco mode, significantly reducing maintenance and replacement costs. Furthermore, they come with eco-friendly features that contribute to lower energy consumption, aligning with sustainability goals while delivering robust performance.

In conclusion, the Mitsubishi Electronics XD470U/XD470U-G projectors are built to meet the demands of modern business and education settings. With their impressive brightness, advanced color technology, versatile connectivity options, and focus on energy efficiency, they remain a valuable asset for effective presentations and engaging learning environments.
Top Page Image Contents