Mitsubishi Electronics XD470U/XD470U-G user manual Lamp replacement, Interval of lamp replacement

Page 22

Lamp replacement

This projector is equipped with a lamp to project images. This lamp is a consumable. It may burn out or its brightness may decrease during use. In such cases, replace the lamp with a new one as soon as pos- sible. Be sure to replace the lamp with a new lamp separately sold that is exclusive to this projector. Contact your dealer for purchase of the lamp.

Spare lamp for XD470U/XD470U-G: VLT-XD470LP

Caution:

•Do not remove the lamp immediately after using the projector. You may get burned because the lamp very hot after use.

•Before replacing the lamp, press the POWER button to turn off the lamp and wait for two minutes for lamp to cool down. Unplug the power cord from wall outlet and wait one hour for the lamp to cool down completely.

•Do not remove the lamp except for replacement. Careless han- dling can cause injury or fire.

•Do not touch the lamp directly. It may break and cause injury or burn.

•Be sure not to drop the lamp lid screw into the projector. Also be sure not to put metal or any flammable objects inside because it may cause fire or electric shock. If any objects should fall inside, unplug and contact your dealer.

•Install the lamp securely to prevent failure and fire.

•If the lamp should break, small glass fragments may fall out through the grilles and some may remain inside of the projector or the lamp box. When taking the lamp box out, be sure to turn over the projector and hold the handle of the lamp box to avoid injury due to the glass fragments.

•If the lamp should break, never shake the lamp box or hold it in front of your face after removing it. The lass fragments may fall out and cause injury to your eyes.

•When placing the projector upside down to replace the lamp or conduct maintenance, ensure that the projector is securely placed before working with it.

1.

Reverse the projector gently.

 

2.

Loosen the screws (a) using a Phillips

 

 

screwdriver (+), and remove the lamp

 

 

cover (b).

 

3.

Loosen the screws (c) using a Phillips

 

 

screwdriver (+).

 

4.

Pull up the handle.

(a)

5.Pull out the lamp box by the handle while holding the projector.

• Pull the lamp box out of the projec-

 

tor slowly. If it is pulled out quickly,

 

the lamp may break scattering

 

glass fragments.

 

• Do not spill liquid on the removed

 

lamp box or do not place it near any

(b)

flammable object or where children

can reach to prevent injury or fire.

(c)

 

6.Load a new lamp box securely into the

projector in the right orientation.

7. Put the handle back to the original posi- tion.

• Make sure that the handle is locked.

8. Tighten up the screws (c) using a Phil- lips screwdriver (+).

9.

Tighten up the screw (a) using a Phillips

(a)

 

screwdriver (+) to secure the lamp

 

 

cover.

 

Reset of the lamp operation time Plug in the power cord, and reset the lamp operation time by keep pressing the W, X, and POWER buttons on the control panel at the same time.

Important:

• Unless these three buttons are pressed

(b)

 

at the same time, the lamp operation time

 

isn’t reset.

 

•Make sure that the STATUS indicator is lit twice and the lamp oper- ation time is reset successfully.

•The projector doesn’t turn on if the lamp cover isn’t attached securely.

•Be sure to reset the lamp operation time whenever you replace the lamp.

•Do not reset the lamp operation time unless you replace the lamp.

Caution:

•The lamp is fragile. If it is broken, be careful not to cut yourself with glass fragments.

•Contact your dealer for a new lamp.

Interval of lamp replacement

When the lamp shutdown notice is issued, the lamp replacement is recommended even if the lamp is lit normally. Decrease in lumines- cence and/or color brightness indicates that the lamp needs to be replaced. When the lamp operation time exceeds the time elapsed until the lamp shutdown notice*1 is issued, the indicator will blink alter- nately green and red while the lamp is lit (while the lamp is not lit, the indicator will blink red only) and the lamp replacement message will appear on the screen for one minute every time the lamp is turned on. When the lamp operation time exceeds the time elapsed until the lamp shutdown warning*2 is issued, the replacement message (LAMP EXCHANGE) will appear on the screen for one minute at fixed inter- vals*4 thereafter.

When the lamp operation time exceeds the time elapsed until the lamp shutdown*3, the projector automatically shuts off and can’t be used until the lamp is replaced and the lamp operation time is reset.

XD470U/XD470U-G

*1 2250 Hours

*2 2850 Hours

*3 3000 Hours*5

The times above are when LAMP MODE of the INSTALLATION menu is set to LOW. When it is set to STANDARD, this duration will be short- ened.

*4

These intervals vary depending on the lamp mode setting.

*5

When LAMP MODE is set to STANDARD, the time elapsed until

 

the lamp shutdown will be shortened to 2000 hours.

Caution:

•This projector uses a lamp that contains mercury. Disposal of the lamp or the projector with the lamp may be regulated due to envi- ronmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries Alliance: www.eiae.org. (For US only).

EN-22

Page 21 Page 23
Image 22
Page 21 Page 23
Contents XD470U/XD470U-G When using the projector in Europe ShockContents Important safeguards Do not unplug the power cord during operation Do not keep using the damaged projectorDo not look into the lens when the projector is operat- ing Place of installationControl panel OverviewTerminal board Remote control Bottom sideOperation range of the remote control Remote controlBattery installation Reception angle vertical Reception angle horizontalFront projection InstallationLayout of the projector Front projection, ceiling mountingProjector + AV device Basic connectionsProjector + DVD player or Hdtv decoder For analog connection Projector + ComputerFor computer with Mini D-SUB For monitor connectionUsing the adjustment feet rear Adjustment of the projection angleUsing the adjustment feet front PreparationPower-on Basic operationAnamorphic mode Power-offVolume from the speaker Instant Shut DownMenu operation Basic operationMenu operation Feature Signal User No need to adjust in normal useImage adjustment Image adjustmentColor temperature Adjustment of the image from the computer Simple adjustment methodTo resume the motion in the image Advanced featureStill Page-up and page-downTo cancel the password function Password functionTo enable the password function Lamp replacement Interval of lamp replacementTroubleshooting Images aren’t projected on the screenTroubleshooting Images aren’t projected correctlyCleaning of the lens MaintenanceCleaning of the projector and the ventilation slots OthersNormal condition IndicatorsAbnormal condition Specifications Replacement part ConnectorsDimensional drawings unit mm What’s included in the boxSignal mode Resolution Horizontal Vertical Mitsubishi Electric Corporation

XD470U/XD470U-G specifications

The Mitsubishi Electronics XD470U/XD470U-G are advanced digital projectors designed for business and educational environments, providing high-quality images and a range of features that enhance presentations and learning experiences. Notable for their versatility, these projectors can accommodate various applications, making them an ideal choice for conference rooms, classrooms, and auditoriums.

At the heart of the XD470U/XD470U-G is a powerful imaging system that delivers stunningly bright and vivid visuals. With a brightness rating of 4500 ANSI lumens, these projectors ensure clarity even in well-lit rooms. They feature a native resolution of XGA (1024 x 768), which is compatible with a wide range of content types, from text to intricate graphics, ensuring that every detail is clearly visible.

One of the standout technologies in the XD470U/XD470U-G is its advanced Color Management technology which produces exceptional color accuracy. This technology helps in achieving vibrant colors that maintain their integrity across various viewing conditions. Coupled with a contrast ratio of 2000:1, the projectors offer deep blacks and bright whites, enhancing the overall quality of the visual experience.

The XD470U/XD470U-G projectors are equipped with a variety of input options, including HDMI, VGA, and USB, making connectivity seamless and adaptable to different devices. Additionally, the inclusion of RS-232 control allows for easy integration with existing AV systems, providing flexibility for users who require advanced management options.

Portability is another key feature, with a compact design and lightweight build enabling easy transportation between locations. This makes the XD470U/XD470U-G ideal for mobile professionals who often conduct presentations in different venues.

The projectors also boast an extended lamp life of up to 6000 hours in eco mode, significantly reducing maintenance and replacement costs. Furthermore, they come with eco-friendly features that contribute to lower energy consumption, aligning with sustainability goals while delivering robust performance.

In conclusion, the Mitsubishi Electronics XD470U/XD470U-G projectors are built to meet the demands of modern business and education settings. With their impressive brightness, advanced color technology, versatile connectivity options, and focus on energy efficiency, they remain a valuable asset for effective presentations and engaging learning environments.
Top Page Image Contents