Onkyo TX-NR808 instruction manual THX Audio Setup, Bgc

Page 48

THX Audio Setup

With the “Surr Back Speaker Spacing” setting, you can specify the distance between your surround back speakers. If you’re using a THX-certified subwoofer, set the “THX Ultra2/Select2 Subwoofer” setting to “Yes”. You can then apply THX’s Boundary Gain Compensation (BGC) to compensate the perceived exaggeration of low frequen- cies for listeners sitting very close to a room boundary (i.e., wall).

You can also set the THX Loudness Plus. When the

Loudness Plus” is set to “On”, it is possible to enjoy even subtle nuances of audio expression at low volume. This result is only available when the THX listening mode is selected.

Surr Back Speaker Spacing

`< 1ft (< 0.3m):

Select this if your surround back speakers are between 0 and 1 foot (0–30 cm) apart.

`1ft - 4ft (0.3m - 1.2m):

Select this if your surround back speakers are between 1 and 4 feet (0.3–1.2 m) apart.

`> 4ft (> 1.2m):

Select this if your surround back speakers are more than 4 feet (1.2 m) apart.

Note

Cannot be set if “Surr Back Ch” is set to “1ch” (46),

Speakers Type(Front)” is set to Bi-Amp (45), “Surr Back” is set to “None” (46), or Powered Zone 2 is being used (71).

THX Ultra2/Select2 Subwoofer

`No:

Select this if you do not have a THX-certified sub- woofer.

`Yes:

Select this if you have a THX-certified subwoofer.

Note

If the “Subwoofer” setting is set to “No”, this setting cannot be selected (46).

BGC

`Off:

Select this to turn off BGC.

`On:

Select this to turn on BGC.

Note

This setting is only available if “THX Ultra2/Select2 Sub- woofer” is set to “Yes”.

Loudness Plus

`Off:

Select this to turn off Loudness Plus.

`On:

Select this to turn on Loudness Plus.

Preserve THX Settings

`Yes:

Audyssey Dynamic EQ® /

Audyssey Dynamic Volume® will not be active in THX listening mode.

`No:

Audyssey Dynamic EQ /

Audyssey Dynamic Volume will be active in THX listening mode depending on the setting.

Note

• This setting is fixed at “Yes” if “Loudness Plus” is set to “On”.

THX Loudness Plus

THX Loudness Plus is a new volume control technology featured in THX Ultra2 Plus™ and THX Select2 Plus™ Certified receivers. With THX Loudness Plus, home theater audiences can now experience the rich details in a surround mix at any volume level. A consequence of turning the volume below Reference Level is that cer- tain sound elements can be lost or perceived differently by the listener. THX Loudness Plus compensates for the tonal and spatial shifts that occur when the volume is reduced by intelligently adjusting ambient surround channel levels and frequency response. This enables users experience the true impact of soundtracks regard- less of the volume setting. THX Loudness Plus is auto- matically applied when listening in any THX listening mode. The new THX Cinema, THX Music, and THX Games modes are tailored to apply the proper THX Loudness Plus settings for each type of content.

En

48

Image 48
Contents TX-NR808 Always consider the environmental issues and follow 10 cm 4 at the rear. The rear edge of the shelf orBoard above the apparatus shall be set 10 cm Away from the rear panel or wall, creating a flue-likePrecautions Supplied Accessories Using the Remote ControllerInstalling the Batteries Aiming the Remote ControllerContents Features AmplifierProcessing MiscellaneousTHX Select2 Plus Amplifier is prohibitedFront & Rear Panels Front PanelSAT , Game , PC , AUX , Tuner , TV/CD , Phono Return button Setup MIC jack DisplayPhones jack Zone 2, Zone 3 and OFF buttons AUX Input jacks HDMI, VIDEO, Audio L/R and Digital 18Rear Panel Hdmi in and Hdmi output Hdmi OUT MainFront L/R, CENTER, Surr L/R SB/FH/FW L/R, SUBWOOFER, Zone 2 L/R and Zone 3 L/RRemote Controller Controlling the AV ReceiverAbout Home Theater Enjoying Home TheaterConnecting the AV Receiver Connecting Your SpeakersSpeaker Configuration Speaker Connection PrecautionsConnecting the Speaker Cables Screw-type speaker terminals Strip 1/2 to 5/8 12 to 15 mmUsing Dipole Speakers Connecting a Powered SubwooferBi-amping the Front Speakers Connecting a Power Amplifier Power amplifierPowered subwoofer About AV Connections Connected image with AV componentsAV Cables and Jacks Hdmi cableConnecting Your Components with Hdmi Jack Signal Components AssignableAudio return channel ARC function Connecting Your Components Front RearConnecting Onkyo uComponents How to record the videoRemote Control StepConnecting Antenna Connecting the Power CordNorth American Taiwan models Asian modelsWhich Connections Should I Use? Video Connection FormatsReceiver’s Hdmi OUT Main and Hdmi OUT SUB to your TVsMonitor Out setting set to Analog Use this setting if you connect the AV receiver’s CompoVideo Signal Flow and the Resolution Setting Audio Connection FormatsStandby indicator Turning On/Off the AV ReceiverTurning On Turning OffSelecting the Language Used for the Onscreen Setup Menus Setting the Display BrightnessBasic Operations Playing the Connected ComponentMuting the AV Receiver Using the Home Menu Using the Sleep TimerSelecting Speaker Layout Using Headphones Using Easy MacrosChanging the Input Display Press MY MOVIE, MY TV, or MY MusicAudyssey MultEQ Room Correction and Speaker Setup Restoring DefaultUsing Audyssey MultEQ Turning Off the ComponentsEnter Error Messages Changing the Speaker Settings ManuallyUsing a Powered Subwoofer Using the Tuner Tuning into Radio StationsListening to the Radio Listening to the RadioPresetting FM/AM Stations Using RDS excluding North American and Taiwan modelsFinding Stations by Type PTY Listening to Traffic News TPRDS program types PTY Connecting a Recording Component RecordingRecording Separate AV Sources AV RecordingUsing the Listening Modes Listening Mode ButtonsSelecting Listening Modes About Listening Modes Explanatory NotesInput Source Speaker LayoutListening Modes DTS-HD Master AudioDTS Express DSD *6Listening Mode Description Input Speaker Source Layout Onkyo-Original DSP Listening Modes Advanced Setup On-screen Setup MenusCommon Procedures in Setup Menu MenuInput/Output Assign Monitor OutOUT OUT MainChanging Monitor Out setting manually ResolutionHdmi Input Here are the default assignments Component Video InputBD/DVD, VCR/DVR, CBL/SAT, GAME, PC TV/CD, PHONO, Port BD/DVD, VCR/DVR, CBL/SAT, GAME, PC, AUX TV/CD, PHONO, PortSpeaker Setup Speaker SettingsDigital Audio Input Analog Audio InputSpeaker Distance Equalizer Settings Level CalibrationSubwoofer*1 EqualizerTHX Audio Setup BGCAudio Adjust Multiplex/MonoDolby Source Setup Theater-DimensionalAudyssey DSX LFE LevelDynamic Volume Reference LevelIntelliVolume SyncName Edit Picture Adjust Listening Mode Preset Hardware Setup MiscellaneousSirius Settings North American models TunerAuto Power Down Firmware UpdateNetwork Lock Setup Using the Audio SettingsTone Control Settings Audyssey SettingsLate Night Re-EQMusic Optimizer Setting the Incoming Digital Signal Fixed Mode Audio SelectorAudio Selector Connecting the AV Receiver About NETNetwork Requirements Listening to Internet Radio Listening to vTuner Internet RadioListening to Other Internet Radio Playback starts and the following screen appearsRegistering Presets*1 Station and Song PresetsPlaying Music Files on a Server Items on the Internet Radio Top MenuWindows Media Player 11 Setup Supported Audio File FormatsMP3 WMAServer Requirements About DlnaWAV AACWindows Media Player 12 Setup Using Remote PlaybackRemote Playback from Media Server/ Personal Computer Supported Music File FormatsNetwork Settings DhcpAbout USB USB Mass Storage Device RequirementsPlaying Music Files on a USB Device Plug your USB mass storage device into the AV Receiver’s USB portPress NET/USB repeatedly to select the USB InputConnecting Zone Connecting Your Zone 2 Speakers Directly to the AV receiverConnecting Your Zone 2 Speakers to an Amp in Zone Multi ZoneConnecting Zone Setting the Powered Zone Connecting Your Zone 3 Speakers to an Amp in ZoneZone 3 12V Trigger Use Front WIDE/ZONE 2 L/R terminals toSetting the Multi Zone Using Zone 2/3Controlling Zone 2/3 from the AV receiver Controlling Zone 2/3 with the Remote Controller Adjusting the Volume for ZonesAdjusting the Tone and Balance of Zones Muting ZonesUsing a Multiroom Kit with Zone 2/3 Using a Multiroom Kit with a CabinetUsing a Multiroom Kit with Other Components Standard Mode control Extended Mode controlPlaying Music Files on the iPod/iPhone Top screen listConnecting an Onkyo Dock Models sold are different depending on the regionOnkyo Dock Cable Using the Onkyo Dock UP-A1 DockControlling Your iPod RI DockWithout the RI Control With the RI ControlAvailable buttons Onkyo Dock Buttons UP-A1 DockUDock E/rENTER PLAYLISTe/rPreprogrammed Remote Control Codes Looking up for Remote Control CodeControlling Other Components AV receiver accesses and searches Network , and then press ENTER. When youSkip when you don’t want to select Use qw/ to select the brand name, and thenEntering Remote Control Codes Remote Control Codes for Onkyo Components Connected via uRemote Mode BD/DVD TV/CDResetting Remote Mode Buttons Resetting the Remote ControllerYou can reset the remote controller to its default settings Controlling Other ComponentsComponents Buttons Cassettetape deckTV VOL q/w Number +10Activities Setup Learning Commands To learn more commands, repeat steps 2Message for transfer will appear Using Normal Macros Deleting Learning CommandsMaking Macros Running MacrosTroubleshooting Standby indicator flashes redThere’s no sound, or it’s very quiet Can’t turn on the AV receiverThere’s no sound with a certain signal format About DTS signalsCan’t select the Pure Audio listening mode Only the center speaker produces soundRemote controller doesn’t work There’s no pictureThere’s no picture from a source connected to an Hdmi On-screen menus don’t appearCan’t learn commands from another remote controller Can’t access the server or Internet radioCan’t access the music files on a USB device Stand-by power consumptionUfunctions don’t work CBL/SAT, GAME, or AUX inputNent Video Monitor OUT Specifications Amplifier Section Tuner SectionGeneral Video SectionAudio Outputs OthersAbout Hdmi Supported Audio FormatsAbout Copyright Protection Using an RIHD-compatible TV, Player, or Recorder About p-compatible componentsOperations that can be performed with p connection How to connect and setup Confirm the connecting and settingConfirm the settings Operate with the remote controllerVideo Resolution Chart OutputOutput Memo Onkyo Europe Electronics GmbH Onkyo Europe Electronics GmbH UK Branch

TX-NR808 specifications

The Onkyo TX-NR808 is a versatile and powerful AV receiver designed to cater to both audiophiles and home theater enthusiasts. This advanced receiver features a robust 7.2 channel configuration, delivering an impressive 130 watts per channel, providing high-quality sound for any audio content. The TX-NR808 is equipped with a variety of modern technologies that enhance the overall listening experience.

One of the standout features of the TX-NR808 is its compatibility with various surround sound formats. It supports Dolby TrueHD and DTS-HD Master Audio, ensuring that high-definition Blu-ray audio is reproduced with maximum fidelity. The receiver also offers Dolby Pro Logic IIz, which adds an extra dimension to your audio with overhead sound, providing a more immersive experience.

The TX-NR808 incorporates the latest HDMI specifications, featuring six HDMI inputs and two outputs, allowing for seamless switching between multiple devices such as gaming consoles, Blu-ray players, and streaming devices. This receiver supports 3D video and 4K pass-through, making it a future-proof choice for those looking to integrate the latest technology into their home theater systems.

For music lovers, the Onkyo TX-NR808 includes network streaming capabilities, allowing users to access music from online services such as Spotify and Pandora. With built-in Wi-Fi and Ethernet connectivity, users can stream high-definition audio directly from their devices. Additionally, the receiver supports playback of high-resolution audio formats, including FLAC, DSD, and WAV, ensuring that every note and nuance is preserved.

Another notable feature is the incorporation of the Audyssey MultEQ technologies. This system automatically calibrates the speakers to the room's acoustics, optimizing the sound quality based on the specific environment. The TX-NR808 also includes Audyssey Dynamic EQ, which maintains sound clarity at lower volume levels.

In addition to its impressive audio capabilities, the Onkyo TX-NR808 is designed with practicality in mind. Its graphical user interface is user-friendly, making setup and navigation a breeze. The sleek and modern design ensures that it can fit seamlessly into any home entertainment setup.

Overall, the Onkyo TX-NR808 is a powerhouse of an AV receiver that combines cutting-edge technology with user-friendly features. Whether for movies, music, or gaming, this receiver is engineered to elevate your audio-visual experience to new heights, making it a worthy investment for any home theater enthusiast.