Mitsubishi HC1100 Risk of Electric Shock Do not Open, When using the projector in Europe

Page 2

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION:

TO PREVENT ELECTRIC SHOCK, DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

NOTE:

SINCE THIS PROJECTOR IS PLUGGABLE EQUIPMENT, THE SOCKET-OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE.

WARNING

Use the attached specified power supply cord. If you use another power supply cord, it may cause interference with radio and television reception.

Use the attached RGB cable and RS-232C cable with this equipment so as to keep interference within the limit of a FCC Class B device.

This apparatus must be grounded.

DO NOT LOOK DIRECTLY INTO THE LENS WHEN THE PROJECTOR IS IN THE POWER ON MODE.

CAUTION

Not for use in a computer room as defined in the Standard for the Protection of Electronic Computer/ Data Processing Equipment, ANSI/NFPA 75.

When using the projector in the U.S.A, use the

specified power cord (246C483-10). For details, please contact your dealer.

When using the projector in Europe:

COMPLIANCE NOTICE

This Projector complies with the requirements of the EC Directive 89/336/EEC “EMC Directive” as amended by Directive 92/31/EEC and 93/68/EEC, and 73/23/ EEC “Low Voltage Directive” as amended by Directive 93/68/EEC.

The electro-magnetic susceptibility has been chosen at a level that gains proper operation in residential areas, on business and light industrial premises and on small-scale enterprises, inside as well as outside of the buildings. All places of operation are characterised by their connection to the public low voltage power supply system.

WARNING

Use the attached RGB cable and RS-232C cable with this equipment so as to keep interference within the limits of an EN55022 Class B device.

Please follow WARNING instructions.

EN-2

Page 1 Page 3
Image 2
Page 1 Page 3
Contents HC1100 When using the projector in Europe Risk of Electric Shock Do not OpenContents Important safeguards EN-4Never remove the cabinet Do not modify this equipment Do not keep using the damaged projectorDo not unplug the power cord during operation Do not face the projector lens to the sunPreparing your projector Checking accessoriesInserting the batteries into the remote control USB terminal OverviewControl area Terminal panel Trigger terminalAdjustment foot Front Lamp cover Adjustment feet Rear Remote controlUsing the picture quality adjusting buttons Preparing your projectorReception angle Using the remote controlOperational range of the remote control Front of projector Rear of projectorBasic setup Setting up your projectorSetting up the screen Adjusting the projection angleTrigger terminal With the Installation menu See page 24 for menu settingTo cancel the menu When the aspect ratio of the image is Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceBasic home theater system connection Connecting the projector to video equipmentViewing video images PreparationWhen a TV tuner or VCR is connected Connecting to a video player, etcConnecting to a DVD player or Hdtv decoder Viewing video imagesConnection for video equipment having an Hdmi terminal Connection for video equipment having a DVI-D terminalPlugging in the power cord Projecting images Following cases When projected images are distorted to a trapezoidTo stop projecting With the remote control Setting the aspect ratioHow to change the settings With the Feature menuViewing computer images Connecting the projector to a computerPlugging the power cord For analog connectionProjecting images Viewing computer images When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonMenu operation Menu operation How to set the menusAvailable settings in the menus Image menuInstallation menu Feature menuTo enable the stored image quality settings Signal menuTo store the settings AV memoryTo adjust the color Color and Tint Adjusting projected imagesTo adjust the brightness Contrast and Brightness To sharpen or soften the projected image SharpnessAbout color temperature Adjusting projected imagesTo adjust the tone of white Color Temp To adjust the ratio of change in brightness Gamma ModeTo adjust the vertical position LPFTo enable the password function Advanced featuresPassword function To cancel the password functionInterval of lamp replacement Replacing the lampReset of the lamp operation time Cleaning of the projector and the ventilation slotsCleaning of the lens Replacing the lampSolution TroubleshootingProblem No image appears on the screenProblem Solution TroubleshootingNo image appears on the screen Problem Solution Images are not displayed correctlyOthers Problem Solution Kensington LockNormal condition IndicatorsPower Status Condition Possible Solution Abnormal conditionDimension drawings unit mm SpecificationsSpecifications ConnectorsReplacement part Option/not included in the box VLT-HC910LPMitsubishi Projector Contact Information
Top Page Image Contents