Onkyo TX-SR600/600E Connecting speakers, Connecting a subwoofer, Connecting the speaker cable

Page 31

Connecting speakers

Connecting speakers

After determining the layout of your speaker system, it is now necessary to connect the speakers correctly to your TX-SR700/ 700E/600/600E.

Caution:

SPEAKER B (TX-SR600/600E only)

1. Strip away approx. 3/8 inch (10 mm) of the wire insulation.

3/8"

(10mm)

•Be sure to connect the positive (+) and negative (–) cables for the speakers properly. If they are mixed up, the left and right signals will be reversed and the audio will sound unnatural.

•Do not connect more than one speaker cable to one speaker terminal. Doing so may damage the TX-SR700/700E/600/600E.

•When you listen to surround audio or select Multichannel, be sure to turn on SPEAKERS A.

•Connect only speakers with an impedance between 6 and 16 Ω to the TX-SR700/700E/600/600E. Connecting speakers with an impedance lower than 6 Ω may damage the amplifier.

•Even if you are using only one speaker or listening to monaural (mono) sound, never connect a single speaker in parallel to both the right and left-channel terminals.

SPEAKERS

 

SPEAKERS

–

+

 

–

+

L

L

L

 

L

 

 

 

R

R

R

 

R

 

 

 

–

+

 

–

+

•To prevent damage to circuitry, never short-circuit the positive

(+) and negative (–) speaker wires.

2. Twist the wire ends tightly together.

3. Press the lever to open the terminal.

4. Insert the exposed wire end.

5. Release the lever to close the terminal. Leave some of the exposed wire showing outside the terminal.

Connecting a subwoofer

Use the SUBWOOFER PRE OUT jack to connect a subwoofer with a built-in power amplifier. If your subwoofer does not have a built-in amplifier, connect an amplifier to the SUBWOOFER PRE OUT jack and the subwoofer to the amplifier.

NO!

Connecting the speaker cable

1. Strip away approx. 5/8 inch (15 mm)

5/8"

(15mm)

of the wire insulation.

 

 

 

 

 

2. Twist the wire ends tightly together.

3. Unscrew the speaker terminal cap.

4. Insert the exposed wire end.

5. Screw down the speaker terminal cap.

Connecting to the SPEAKERS B terminals (TX-SR600/600E only)

If you require an additional set of front speakers (left and right), such as for use in another room, connect them to the FRONT SPEAKERS B inputs.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents TX-SR700/700E TX-SR600/600E Avis Important SafeguardsPrecautions Contents Contents TX-SR700/700E Amplifier Features FeaturesUsing the remote controller Supplied accessoriesBefore using this unit Setting the voltage selector Worldwide models onlyTX-SR700E TX-SR600E Front panel facilitiesFront panel facilities TuningSpeakers A/B buttons TX-SR600/600E only Pure Audio button and indicator TX-SR700/700E only 49Audio Selector button Phones jackSleep indicator Muting indicatorListening mode or digital input format indicators Tuning indicatorsRemote controller Remote controller Connections Connections Connections TX-SR700/700E Connecting your audio componentsConnecting a compact disc player CD Signal flowConnecting a DVD Player with 5.1-Channel Output Connecting your video componentsFlow of the video signals is as follows Connecting a DVD player DVD Connecting a DVD Player with 2-Channel L/R Audio OutputConnecting a video cassette recorder Video Monitor OUT Connecting a television monitor or projector Monitor OUTFront right speaker Connecting video camera, etc. Video 4 InputPower amplifier 12V Trigger Zone 2 terminalFrom connecting block TX-SR700/700E only Connecting the remote zone Zone 2 speakersWhen using the Zone 2 PRE OUT terminals When using the Zone 2 Speakers terminalsConnections TX-SR600/600E Video 3 Video White Analog audio output Red Digital audio output coaxial Satellite tuner or television Video 2/3 Front panel OUTDirect change function Power on/ready functionPower off function Connections TX-SR700/700E/600/600ESpeaker placement Connecting speakersStandard speaker setup for surround sound Minimum speaker configuration for surround sound playbackConnecting the speaker cable Connecting speakersConnecting speakers Connecting a subwooferSubwoofer Surround Front Center Right Speaker LeftRight Back Left Speaker Turning on the power Connecting the powerTurning on the power from the remote controller Assembling the AM loop antenna Connecting antennasConnecting the included antennas Connecting the AM antenna cableDirectional linkage Connecting antennasConnecting an FM outdoor antenna Connecting an AM outdoor antennaDisplaying the Main Menu Configuring the speakersSpeaker Configuration Return Setup EnterAdjustable Crossover 80/100/120 Hz for Bass Management Configuring the speakersMain menu and then press the Enter button Calibrating the speaker levelsUse the and cursor buttons to select Left Displaying the Main Menu and exiting the menu Using the remote controller Press the Test buttonPress the Test button to complete the procedure Buttons used for navigating through the menusListening to Radio Broadcasts Listening to a stereo radio station FM modeTuning into a radio station FM Mode Tuner TuningListening to Radio Broadcasts Presetting a radio stationSelecting a preset radio station Erasing a preset radio stationPTY program types in Europe What is RDS?Listening to RDS broadcasts European models only Listening to RDS broadcastsPerforming a TP scan Listening to RDS broadcastsDisplaying Radio Text RT Performing a PTY scanMode Master VolumeSelecting an Audio Component Basic operation TX-SR700/700ESelecting speakers Speakers A, B TX-SR600/ 600E only Speakers A/B Rcvr ModeSelecting an Audio Component Basic operation TX-SR600/600ECH SEL Audio SEL Level TAP Tape Audio Selector Selecting the type of audio input signalTemporarily changing the speaker output levels To change the display of the input source from Tape to MDTX-SR700/700E only Using the sleep time remote controller onlyListening with headphones Enjoying DVD multichannel audio playbackTemporarily turning off the sound Switching the displayListening Modes Listening Modes While playing back Dolby Digital 2-channel sources Selecting a listening modeTip Cine FltrOriginal filter CinemaFILTER loading for movies Press the Cine Fltr button on the remote controllerDigital Input Input SetupSetup Menu ReturnMultichannel Input SetupIntelliVolume Digital FormatDigital Format Source Relationship between input source and listening modeAnalog/PCM Source PCM fs96kHz SourcePreference OSD Setup and Other SettingsOSD Setup To display the OSD Setup menuBass, Treble Audio AdjustSetup Procedure Press the Audio Adjust button Setting Values Initial valueAudio Adjust Night Settings possible for each listening modeZone Level Standby Sleep OFF Using the buttons on the TX-SR700/700EAdjusting the volume for the remote zone Enjoying music in the remote zone TX-SR700/700E onlyREC OUT Recording a source TX-SR700/700EStart recording at the recording component as desired Recording a source TX-SR600/600E Rcvr Mode VOL Muting Using remote controllerCalling up a preset radio station Rcvr Mode VOLControlling an Onkyo CD player Using remote controllerOn Standby CD Mode Disc Press the CD Mode buttonDVD operation buttons Numeric keys Press the DVD Mode buttonControlling an Onkyo DVD player SearchControlling an Onkyo MD recorder VCR and TV Mode buttonsOn Standby MD Mode TV Mode TV VCR Mode VCR VOL MutingDisplay When entering the code of Onkyo DVD playersEntering a pre-programming code Learning a pre-programming codeVCR Entering a pre-programming codePre-programming codes DVDTV Mode TV Mode Operating your programmed remote controllerDVD Mode DVD Player Mode VCR Mode VCR ModeLight Programming procedureMacro 1 Macro Page Press and release the same button again Erasing the programmed command from one buttonErasing all the commands programmed under a Mode button Press and release the same Mode button againExecuting the macro Using the macro functionMacro 1 Rcvr Mode CD Mode Programming the macroPress the Macro 1 or 2 button again Using the macro functionErasing all commands and macros that have been programmed Erasing a macro from the Macro 1 or 2 buttonMacro mode programming memo Troubleshooting guide Video and Audio Troubleshooting guideIf one of the messages shown below appears Amplifier Section Tuner Section Specifications TX-SR700/700EOnkyo Europe Electronics GmbH Specifications TX-SR600/600E

TX-SR600/600E, TX-SR700/700E specifications

The Onkyo TX-SR700/700E and TX-SR600/600E are renowned audio/video receivers that have significantly enriched the home theater experience since their release. These models exemplify Onkyo’s dedication to high-fidelity sound and advanced technology, making them a favorite among audiophiles and home theater enthusiasts alike.

A standout feature of the TX-SR700/700E is its exceptional audio performance. It boasts a powerful amplification system, providing 100 watts per channel, ensuring immersive sound that fills the room. Additionally, the receiver supports a variety of surround sound formats, including Dolby Digital, DTS, and Dolby Pro Logic II, allowing users to enjoy their favorite movies, music, and games with impressive clarity and depth.

The TX-SR600/600E, while slightly more compact, still delivers remarkable audio performance. With comparable power, this model maintains high-quality sound output and supports a range of listening modes. Both receivers feature Onkyo's proprietary Wide Range Amplification Technology (WRAT), which enhances dynamic sound reproduction while minimizing distortion, ensuring that even the most delicate audio details are preserved.

Connectivity is another strong point for these models. The TX-SR700/700E and TX-SR600/600E come equipped with a variety of HDMI inputs, allowing seamless integration with modern devices. This feature supports high-definition video and audio transmission, making it easy to connect Blu-ray players, gaming consoles, and streaming devices. Furthermore, the receivers are compatible with older technologies, providing versatility for various home entertainment setups.

One notable characteristic of both models is their robust video processing capabilities. They support up to 1080p video resolution and include advanced scaling features, ensuring that standard-definition content looks stunningly sharp on high-definition displays. Additionally, the user-friendly interface and remote control simplify operation, making it easy for users to navigate settings and adjust audio/video parameters quickly.

The TX-SR700/700E and TX-SR600/600E also incorporate advanced digital technologies such as Audyssey MultEQ, which automatically calibrates the audio settings based on room acoustics, providing an optimized listening experience. This feature is crucial in achieving balanced sound in any room environment.

In conclusion, the Onkyo TX-SR700/700E and TX-SR600/600E are exemplary models that combine power, flexibility, and advanced technology. With their rich sound quality, extensive connectivity options, and user-friendly features, these receivers remain a worthwhile investment for anyone looking to enhance their home theater system. Whether for movie nights, gaming, or casual listening, these Onkyo receivers are poised to deliver an unforgettable audio experience.
Top Page Image Contents