Pioneer PDP-502MXE manual Power cord connection, How to route cables, To remove speed clamps

Page 16

Installation and Connections

English

Power cord connection

Connect a power cord after all component connections have been completed.

PDP-502MXE power cord ratings

Cord

Cross-sectional area 3 x 1.0 mm2

 

(According to CEE 13)

Connector

10 A, 250 V

 

(According to EN60320 Sheet C13)

Plug

International use (10 A, 250 V)

Example:

UK : UK 13 Amp Plug with rated 13 Amp fuse (According to BS1363)

EURO : 10 A/16 A 250 V (According to CEE 7, 1 V)

1Organize cables together using the provided speed clamps.

Insert 1 into an appropriate hole on the rear of the unit, then snap 2 into the back of 1 to fix the clamp.

Speed clamps are designed to be difficult to undo once in place. Please attach carefully.

To attach the speed clamps to the main unit

Connect the speed clamps using the 4 holes marked with

• below, depending on the situation.

CAUTION

ÖDo not use a power supply voltage other than that indicated (AC 100 - 240 V, 50/60 Hz) as this may cause fire or electric shock.

ÖFor the plasma display, a three-core power cord with a ground terminal is used for efficiency protection. Always be sure to connect the power cord to a three-pronged grounded outlet and make sure that the cord is properly grounded. If you use a power source converter plug, use an outlet with a ground terminal and screw down the ground line.

To remove speed clamps

Using pliers, twist the clamp 90° and pull it outward. In some cases the clamp may have deteriorated over time and may be damaged when removed.

Installation and Connections

How to route cables

Speed clamps and bead bands are included with this unit for bunching cables together. Once components are connected, follow the following steps to route cables.

2Bunch separated cables together and secure them with the provided bead bands.

Note

Cables can be routed to the right or left.

* As viewed from the rear of the display.

1

1

2

2

12

<ARE1350> En

Page 15 Page 17
Image 16
Page 15 Page 17
Contents PDP-502MXE Page Basic Operations Safety Precautions EnglishFeatures ContentsBefore Proceeding How to Use This ManualAbout operations in this manual Remote control unit Checking supplied accessoriesOperating Instructions Before Proceeding Part Names and Functions Main unitOperation panel on the main unit Main unitRemote control unit Connection panel Main Power switch ~ Speaker L terminalInstallation and Connections Installation of the unitInstallation using the supplied display stand Set this unit in the standRear view diagram Wall-mount installation of the unitSide view diagram When connecting to INPUT3 When connecting to INPUT4When connecting to INPUT4 Output Connection of separate Sync analog RGB sourceConnecting the speakers Audio connectionsControl cord connection Making connections to the audio inputs on this unitPower cord connection How to route cablesOrganize cables together using the provided speed clamps To attach the speed clamps to the main unitSetup of G on Sync Clamp connection Operations Press STANDBY/ON to put this unit in the operation modeBefore you begin, make sure you have To adjust the volume To confirm display settingsPress Muting on the remote control unit To mute the soundScreen size selection Changing the screen sizePress Screen Size to select the size NormalTo put the unit in operation mode again Press SET to select the Power Save modePress 5/ to select PC Menu screenAdjusting the picture quality Display Panel AdjustmentsTo reset Picture mode settings to the default Adjusting the display image To reset Screen mode settings to the defaultPress 2/3 to carry out the adjustment Screen mode adjustment itemsDisplay Panel Adjustments Press 5/ to select ABL Press 5/ to select SET UP, then press SETMaking the PC image brighter ABL Resetting the unit to factory set defaults Press 2/3 to adjustPress 5/ to select H. Enhance or V. ENHANCE, then press SET Press 2 to select YES, then press SETInserting the batteries in the remote control unit CleaningAdditional Information Troubleshooting Operating range of the remote control unitGeneral Problems Problems commonly mistaken as breakdown About the self diagnosis modeAdditional cautions InformationSpecifications AccessoriesPanel sticking and after-image lag GeneralPC signal compatibilty table INPUT3, INPUT4 SupplementExplanation of Terms Aspect ratioPrecautions de securite CommencerFrance tapez 36 15 Pioneer

PDP-502MXE specifications

The Pioneer PDP-502MXE is a remarkable plasma display panel that garnered attention in the home entertainment market due to its superior image quality and exceptional design. Launched in the early 2000s, the PDP-502MXE was a leading model in Pioneer’s lineup of high-definition plasma televisions, showcasing cutting-edge technology that set new standards in the industry.

One of the standout features of the PDP-502MXE is its 50-inch screen, which makes it an ideal choice for home theaters and larger living spaces. The display boasts a native resolution of 1024x768 pixels, providing stunning image clarity and detail. The plasma technology employed in this model allows for deep blacks and vibrant colors, delivering a dynamic range that enhances movie-watching experiences and visual content.

The PDP-502MXE supports multiple aspect ratios and allows users to choose between 4:3 and 16:9, making it versatile for various types of media. It comes equipped with advanced video processing capabilities, ensuring that even lower-resolution signals are upscaled effectively, resulting in a smooth viewing experience. The inclusion of a range of inputs, such as HDMI and component video, makes it compatible with many external devices, including DVD players and gaming consoles.

Additionally, Pioneer integrated their proprietary technologies into the PDP-502MXE, such as the PureCinema technology, which improves motion handling by reducing blurriness during fast-moving scenes. The display also features a filter that minimizes reflections, allowing it to perform admirably in different lighting conditions.

The PDP-502MXE’s design is another highlight, featuring an ultra-slim profile that enhances its aesthetic appeal. The panel's industrial design is complemented by minimal bezels, making it a stylish addition to any home setup. The build quality of the PDP-502MXE reflects its premium positioning, ensuring durability alongside functionality.

In summary, the Pioneer PDP-502MXE is a powerful plasma display that combines impressive visual performance with sleek design. Its advancing technologies, compatibility with various media formats, and stylish aesthetics make it an enduring choice for enthusiasts of high-quality home entertainment systems. Although newer technologies have emerged since its release, the PDP-502MXE continues to be remembered for its significant contributions to the evolution of display technology.
Top Page Image Contents