Pioneer PDP-502MXE manual Safety Precautions, English

Page 4

Safety Precautions

English

IMPORTANT

 

 

CAUTION

 

 

 

RISK OF ELECTRIC SHOCK

 

 

 

DO NOT OPEN

 

The lightning flash with arrowhead symbol, within

CAUTION:

an equilateral triangle, is intended to alert the user to

TO PREVENT THE RISK OF ELECTRIC

the presence of uninsulated “dangerous voltage”

SHOCK, DO NOT REMOVE COVER (OR

within the product’s enclosure that may be of

BACK). NO USER-SERVICEABLE PARTS

sufficient magnitude to constitute a risk of electric

INSIDE. REFER SERVICING TO QUALIFIED

shock to persons.

SERVICE PERSONNEL.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Thank you very much for purchasing this PIONEER product. Before using your Plasma Display, please carefully read the “Safety Precautions” and these “Operating Instructions” so you will know how to operate the Plasma Display properly. Keep this manual in a safe place. You will find it useful in the future.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

CAUTION: This product may be used only with Model PDK-5001 stand. Use with other stands may result in instability causing possible injury.

WARNING: THIS APPARATUS MUST BE EARTHED.

CAUTION: WHEN POSITIONING THIS EQUIPMENT ENSURE THAT THE MAINS PLUG AND SOCKET IS EASILY ACCESSIBLE.

Introduction

WARNING:

This is a Class A product. In a domestic environment this

 

 

product may cause radio interference in which case the

 

user may be required to take adequate measures.

 

 

 

To ensure proper heat radiation, distance the unit slightly from

 

other equipment, walls, etc. (normally mode than 10 cm). Avoid

 

the following installations which will block vents and cause heat

 

to build up inside, resulting in fire hazards.

 

• Do not attempt to fit the unit inside narrow spaces where

 

ventilation is poor

 

• Do not place on carpet

 

• Do not cover with cloth, etc.

 

• Do not place on its side

 

• Do not place it upside down

 

• If planning special installation such as fitting close to the wall,

 

placing it horizontally, etc., be sure to consult your Pioneer

 

dealer first.

i

Notes on Installation Work:

This product is marketed assuming that it is installed by qualified personnel with enough skill and competence. Always have an installation specialist or your dealer install and set up the product. PIONEER cannot assume liabilities for damage caused by mistake in installation or mounting, misuse, modification or a natural disaster.

Note for Dealers:

After installation, be sure to deliver this manual to the customer and explain to the customer how to handle the product.

The following symbols are found on labels attached to the product. They alert the operators and service personnel of this equipment to any potentially dangerous conditions.

WARNING

This symbol refers to a hazard or unsafe practice which can result in personal injury or property damage.

CAUTION

This symbol refers to a hazard or unsafe practice which can result in severe personal injury or death.

<ARE1350> En

Image 4 Contents
PDP-502MXE Page Basic Operations Safety Precautions EnglishFeatures ContentsBefore Proceeding How to Use This ManualAbout operations in this manual Remote control unit Checking supplied accessoriesOperating Instructions Before Proceeding Part Names and Functions Main unitOperation panel on the main unit Main unitRemote control unit Connection panel Main Power switch ~ Speaker L terminalInstallation and Connections Installation of the unitInstallation using the supplied display stand Set this unit in the standRear view diagram Wall-mount installation of the unitSide view diagram When connecting to INPUT3 When connecting to INPUT4When connecting to INPUT4 Output Connection of separate Sync analog RGB sourceConnecting the speakers Audio connectionsControl cord connection Making connections to the audio inputs on this unitPower cord connection How to route cablesOrganize cables together using the provided speed clamps To attach the speed clamps to the main unitSetup of G on Sync Clamp connection Operations Press STANDBY/ON to put this unit in the operation modeBefore you begin, make sure you have To adjust the volume To confirm display settingsPress Muting on the remote control unit To mute the soundScreen size selection Changing the screen sizePress Screen Size to select the size NormalTo put the unit in operation mode again Press SET to select the Power Save modePress 5/ to select PC Menu screenAdjusting the picture quality Display Panel AdjustmentsTo reset Picture mode settings to the default Adjusting the display image To reset Screen mode settings to the defaultPress 2/3 to carry out the adjustment Screen mode adjustment itemsDisplay Panel Adjustments Press 5/ to select ABL Press 5/ to select SET UP, then press SETMaking the PC image brighter ABL Resetting the unit to factory set defaults Press 2/3 to adjustPress 5/ to select H. Enhance or V. ENHANCE, then press SET Press 2 to select YES, then press SETInserting the batteries in the remote control unit CleaningAdditional Information Troubleshooting Operating range of the remote control unitGeneral Problems Problems commonly mistaken as breakdown About the self diagnosis modeAdditional cautions InformationSpecifications AccessoriesPanel sticking and after-image lag GeneralPC signal compatibilty table INPUT3, INPUT4 SupplementExplanation of Terms Aspect ratioPrecautions de securite CommencerFrance tapez 36 15 Pioneer