Oregon Scientific EB833 user manual Deactivating the Alarm, COUNT-UP Timer, Temperature Display

Page 14

 

 

 

 

 

 

 

 

 

 

 

EN

6.

Press [TIME] again to set and activate / deactivated

 

 

 

 

 

 

 

 

 

 

 

 

 

the alarm.

 

 

 

 

7.

Press [+] or [-] to select between activation and

 

 

 

 

 

 

deactivation. The alarm icon will only appear when

 

 

 

 

 

 

the alarm is set.

 

 

 

 

8.

Pressing [TIME] a last time to exit. The ALARM

 

 

 

 

 

 

indicator stops flashing.

 

 

 

 

 

 

 

 

 

 

 

 

NOTE

If no buttons are pressed for 2 minutes during

 

 

 

 

 

setting sequence, the unit will return to Alarm Time

 

 

 

 

 

Display.

DEACTIVATING THE ALARM

When the alarm time is reached the alarm will sound for 1 minute.

To stop the alarm:

Pressing any button can stop the alarm sound.

COUNT-UP TIMER

The unit comes with a count-up timer and can count up to 99 hours 59 minutes and 59 seconds.

To start, stop, and reset the timer:

1.Enter Timer Display.

2.Press [+] the timer starts counting.

3.Press [+] again, the timer stops. To start the timer

again without clearing the elapsed time, press [+].

14

 

 

EB833(EN3)

14

 

4.To reset the timer to 0, press [+] to stop the timer and then press [-].

TEMPERATURE DISPLAY

The current temperature is displayed in all three display modes. The temperature can be displayed as Celsius (°C) and Fahrenheit (°F).

To select the units of measure for the temperature display:

1.Enter Date/Month Mode.

2.Press and hold [+] or [-] for about 2 seconds to change the units of measure.

RESETTING THE UNIT

Located inside the battery compartment is a RESET Button. Using a blunt object such as a paper clip, press RESET to return all settings to the factory values.

The button is required only when the unit is not operating in a favorable way, such as in the rare case of a malfunction.

NOTE After resetting the unit all memories and data will be cleared.

8/31/04, 3:40 PM

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Table of Contents Introduction Description of PartsInstalling and Replacing of Battery General Operation of the Altimeter Follow these steps to install or replace batteriesTo view display sequences in Altimeter Mode Normal Altitude DisplayPress ALT again, Altitude History Display Display show Display Display showsDisplay About the Altitude Change Graph Altitude CalibrationUnits of Measurement for Altitude About Altitude Change Memory To clear Altitude Mode MemoriesAltitude History Display To numerically display previous altitude levelsNormal Altimeter Display Altitude AlarmAltitude Sampling Rate Barometer and Weather Forecast Functions To ensure that accurate altitude readings are maintainedBarometric Calibrations Units of Measure for Barometric PressureTonumericallydisplaypreviousbarometricpressure levels About the Pressure Change GraphPressure History Display To ensure that accurate barometric readings are maintainedGeneral Operation of the Time and Date Functions To View Different Time and Date Mode displaysPress Time again to view the Timer Display Display shows Normal Time DisplayTime and Date Daily AlarmTo Set the Alarm Time Current time and date can be set sequentiallyTemperature Display Deactivating the AlarmCOUNT-UP Timer Resetting the UnitBarometer Functions Maintenance SpecificationsAltimeter Functions Thermometer FunctionsCalendar Clock Functions Time resolution SecondTimer Functions Hours formatAbout Oregon Scientific Call 949-608-2848 in the USOregon Scientific. All rights reserved EB833EN3 31/04, 340 PM
Top Page Image Contents