Mitsumi electronic XD3500U user manual Front projection, ceiling mounting, Rear projection

Page 12

Setting up your projector (continued)

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation. For details, consult your dealer.

•The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

•When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 30.

•When the projector is mounted on the ceiling, images may appear darker than those projected in the case of tabletop mounting. This isn’t a product malfunction.

•Ask your installation specialist to provide a breaker. When you do not use the projector, be sure to shut down the main power by the breaker.

•Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a breakdown.

•Do not install the projector near a ﬁre alarm because it emits hot air from its exhaust vents.

Rear projection

Ask a specialist for installation. For details, consult your dealer.

•For rear projection, set IMAGE REVERSE in the INSTALLATION menu to MIRROR. See page 30.

Caution:

•Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the projector to facilitate ventilation.

•Place the projector at least 50 cm (or 20 inches) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

•Do not use the projector in the following locations and manners, which may cause ﬁre or electric shock.

•In a dusty or humid place.

•In a sideways position, or with the lens facing down.

•Near a heater.

•In an oily, smoky, or damp place such as a kitchen.

•In direct sunlight.

•Where the temperature rises high, such as in a closed car.

•Where the temperature is lower than +41ºF (or +5ºC) or higher than +95ºF (or +35ºC).

Important:

•We don’t recommend using the projector at an altitude of 1500 meters or higher. Use at an altitude of 1500 meters or higher may affect the projector’s life.

EN-12

Image 12

Contents XD3500 EN-2 Contents Important safeguards Important safeguards Do not keep using the damaged projectorChecking accessories Inserting the batteries into the remote controlPreparing your projector Preparing your projector OverviewControl area Terminal panelRemote control Bottom sideAbout the laser beam Using the remote control Operational range of the remote controlUsing the wired remote control Reception angleSetting up your projector Setting up the screenScreen size and projection distance Front projectionSetting up your projector Adjusting the position of the projected imageWhen ﬁne streaks are seen on projected images When projected images are distorted to a trapezoidFront projection, ceiling mounting Rear projectionConnecting the projector to a computer Viewing computer imagesPlugging the power cord Viewing computer imagesAbout DDC For monitor connectionInstalling the terminal cover Projecting images Remove the lens capDirect Power OFF To stop projectingWhen connecting to a notebook computer Setting of the resolutionExample of the setting procedure for external output AV muteConnecting the projector to video equipment Connecting to a video player, etcViewing video images Viewing video images Projector + DVD player or Hdtv decoderConnection for video equipment having an Hdmi terminal Plugging in the power cord Connection for video equipment having a DVI-D terminalEN-22 EN-23 Volume from the speaker Setting the aspect ratioHow to change the settings With the remote control Menu display mode and menu type Menus displayed in the Quick Menu modeMenus displayed in the Detail Menu mode Menu operationBasic procedure for setting the menus Menu operationSettings of each menu item Quick MenuEN-28 Image menu Advanced MenuEN-30 EN-31 Signal menu UserAdjusting projected images To adjust the brightness Contrast and BrightnessTo adjust the color Color and Tint To adjust the tone of white Color TempAdjusting projected images About color temperatureColor Enhancer How to adjust the computer image YESSimple method to adjust the image position To adjust the horizontal positionTo adjust the vertical position LPF Progressive ﬁlterAdvanced features Setting procedureAdvanced features Password functionTo cancel the password function To enable the password functionPicture in Picture PinP Magnifying the displayed imageFreeze Mouse remote control Projector + computer with USB connectorOperation UP buttonSupervising and controlling by computer Major functionsConnection Indicators Normal conditionAbnormal condition Interval of lamp replacement Replacing the lampReset of the lamp operation time Replacing the lampTo replace the lamp Maintenance Cleaning of the projector and the ventilation slotsCleaning of the lens When removing the lamp from the ceiling-mounted projectorTroubleshooting No image appears on the screen Problem SolutionTroubleshooting Images are not displayed correctly Problem SolutionOthers Problem Solution EN-49 Replacement part option/not included in the box SpeciﬁcationsSpeciﬁcations XGA85Connectors Dimension drawings unit mmWithout terminal cover Mitsubishi Electric Corporation