Mitsumi electronic HC6500 Front projection, ceiling mounting, Rear projection, Trigger terminal

Page 13

Setting up your projector (continued)

Front projection, ceiling mounting

For ceiling mounting, you need the ceiling mount kit designed for this projector. Ask a specialist for installation. For details, consult your dealer.

•The warranty on this projector does not cover any damage caused by use of any non-recommended ceiling mount kit or installation of the ceiling mount kit in an improper location.

•When using the projector mounted on the ceiling, set IMAGE REVERSE in the INSTALLATION menu to MIRROR INVERT. See page 27.

•When the projector is mounted on the ceiling, images may appear darker than those projected in the case of tabletop mounting. This isn’t a product malfunction.

•Ask your installation specialist to provide an A/C power switch. When you do not use the projector, be sure to shut down the main power by the switch.

•Do not install the projector where the exhaust vents are exposed to air emitted by an air conditioning. Such installation may cause a breakdown.

•Do not install the projector near a fire alarm because it emits hot air from its exhaust vents.

Rear projection

Ask a specialist for installation. For details, consult your dealer.

• For rear projection, set IMAGE

REVERSE in the

INSTALLATION menu to MIRROR. See page 27.

Important:

•We don’t recommend using the projector at an altitude of 1500 meters or higher. Use at an altitude of 1500 meters or higher may affect the projector’s life.

TRIGGER terminal

The TRIGGER terminal on the rear of the projector is a terminal that outputs a 12 V signal to control an externally connected device (electric screen) when images are projected.

TRIGGER

To externally connected device

Ring (NC)

Tip (12 V)

(Ground 0 V)

To use the TRIGGER terminal, set TRIGGER OUT to SCREEN or ANAMORPHIC in the INSTALLATION menu. (The factory default is OFF. See page 27 for details.) Use the following steps to change the setting.

With the INSTALLATION menu:

(See page 26 for menu setting.)

1.Display the INSTALLATION menu.

2.Select TRIGGER OUT by pressing the S or T button.

3.Select SCREEN or ANAMORPHIC by pressing the W or X button.

To cancel the menu:

Caution:

•Placing the projector directly on a carpet impairs ventilation by the fans, causing damage or failure. Put a hard board under the projector to facilitate ventilation.

•Place the projector at least 50 cm (or 20 inch) away from the wall to prevent the air inlet grille and the air outlet grilles that emit hot air from being blocked.

•Do not use the projector in the following locations and manners, which may cause fire or electric shock.

•In a dusty or humid place.

•In a sideways position, or with the lens facing down.

•Near a heater.

•In an oily, smoky, or damp place such as a kitchen.

•In direct sunlight.

•Where the temperature rises high, such as in a closed car.

•Where the temperature is lower than +41ºF (or +5ºC) or higher than +95ºF (or +35ºC ).

4. Press the MENU button.

Caution:

•Do not use the signal output from the TRIGGER terminal as a power for other devices.

•Do not link the TRIGGER terminal with an audio terminal of other device because that device may be damaged.

•The rated current for the TRIGGER terminal is

200 mA. If you use a current exceeding this rating, a failure may occur.

•For information about electric screens, please contact screen manufacturers.

EN-13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents HC6500 Risk of Electric Shock Do not Open When using the projector in EuropeContents Important safeguards Important safeguards Inserting the batteries into the remote control Checking accessoriesRemoving the batteries from the remote control Preparing your projectorPreparing your projector Indicator area Control panel Terminal panelOverview Attaching the lens capUsing the picture quality adjusting buttons Remote controlAdjustment feet Bottom sideOperational range of the remote control Using the remote controlReception angle Setting up the screen Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceWhen the aspect ratio of the screen is 2.351 CinemaScope Setting up your projectorWhen the aspect ratio of the image is When fine streaks are seen on projected images Adjusting the position of the projected imageWhen projected images are distorted to a trapezoid Correcting skewed or distorted imageRear projection Front projection, ceiling mountingTrigger terminal Viewing video images Connecting the projector to video equipmentBasic home theater system connection PreparationConnecting to a DVD player or Hdtv decoder Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesConnection for video equipment having an Hdmi terminal Connecting to video equipment having a Hdmi terminalPlugging in the power cord Projecting images To stop projecting ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2 Setting the aspect ratioWith the remote control How to change the settingsWith the Feature menu See page 26 for menu setting Plugging the power cord Connecting the projector to a computerViewing computer images About DDCComputer Viewing computer imagesSetting of the resolution When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonMenu operation Available settings in the menus How to set the menusMenu operation Image menuInstallation menu Feature menu User menu Signal menuTo enable the stored image quality settings To store the settingsAV memory Information menuTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature To enable the stored color temperatureNoise reduction To adjust the ratio of change in brightness Gamma ModeLPF Progressive filter To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionReplacing the lamp Interval of lamp replacementReplacing the lamp Reset of the lamp operation timeTo replace the lamp When removing the lamp from the ceiling-mounted projector Cleaning of the air-filter MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution TroubleshootingOthers Problem Solution Condition Possible Solution IndicatorsNormal condition Abnormal conditionSpecifications Dimension drawings unit mmSpecifications Replacement part option/not included in the box ConnectorsComputer IN/COMPONENT Video Hdmi VLT-HC7000LPMitsubishi Electric Corporation

HC6500 specifications

The Mitsumi HC6500 is an innovative electronic component that has garnered attention for its versatile features and advanced technologies. This device is primarily known for its role as a high-performance connectivity solution in various electronic applications. The HC6500 stands out in the crowded market of electronic components by incorporating several key characteristics that enhance its overall functionality and usability.

One of the main features of the HC6500 is its wide compatibility with various communication protocols. This allows it to easily integrate into different systems, whether they are automotive, industrial automation, or consumer electronics. The device supports both wired and wireless communication, making it a flexible option for designers looking to streamline their connectivity solutions.

The HC6500 also boasts a compact design, which reduces space requirements in circuit designs. Its form factor is particularly beneficial for applications where space is at a premium, such as in portable devices and IoT gadgets. This small footprint does not compromise performance, as the HC6500 delivers robust connectivity with high data transfer rates that cater to the demands of modern applications.

In terms of power efficiency, the HC6500 is engineered to operate with low power consumption, which is essential for battery-operated devices. This energy efficiency is complemented by its advanced thermal management features, ensuring stable performance even under heavy loads or extended use.

The device also incorporates sophisticated error correction technologies, which enhance data integrity during transmission. This is particularly vital in critical applications, such as medical devices and automotive systems, where data accuracy is non-negotiable. The HC6500’s ability to maintain a reliable connection under various environmental conditions is another hallmark of its design.

Furthermore, the HC6500 is built with an emphasis on durability. Its materials and construction are designed to withstand extreme temperatures, vibrations, and other challenging conditions often encountered in industrial and outdoor environments. This reliability ensures that the HC6500 can perform consistently over a long lifespan, reducing maintenance and replacement costs.

Overall, the Mitsumi HC6500 is a well-rounded electronic component that combines cutting-edge technology with practical features, making it an excellent choice for designers and engineers looking to enhance their products with reliable connectivity solutions.
Top Page Image Contents