Mitsumi electronic HC6500 user manual Plugging in the power cord

Page 17

Viewing video images (continued)

B. Plugging in the power cord

•In order to ensure the safety in case of trouble with the projector, use an electrical outlet having an earth leakage breaker to supply the power to the projector. If you do not have such outlet, ask your dealer to install it.

Earthing terminal

2

1

Power cord (example)

1.Plug the attached power cord into the power cord inlet of this projector.

2.Plug the other end of the power cord into a power outlet.

•The power cords for use in the U.S. and Europe are included with this projector. Use the appropriate one for your country.

•This projector uses the power plug of three-pin grounding type. Do not take away the grounding pin from the power plug. If the power plug doesn’t ﬁt your wall outlet, ask an electrician to change the wall outlet.

•The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or power supply using other voltages or frequencies than rated. If you use a power supply using other voltage than rated, prepare an appropriate power cord separately.

•Use 100-240 V AC 50/60 Hz to prevent ﬁre or electric shock.

•Do not place any objects on the power cord or do not place the projector near heat sources to prevent damage to the power cord. If the power cord should be damaged, contact your dealer for replacement because it may cause ﬁre or electric shock.

•Do not modify or alter the power cord. If the power cord is modiﬁed or altered, it may cause ﬁre or electric shock.

Caution:

•Plug in the power cord ﬁrmly. When unplugging, hold and pull the power plug, not the power cord.

•Do not plug in or out the power cord with your hand wet. It may cause electric shock.

EN-17

Image 17

Contents HC6500 Risk of Electric Shock Do not Open When using the projector in EuropeContents Important safeguards Important safeguards Inserting the batteries into the remote control Checking accessoriesRemoving the batteries from the remote control Preparing your projectorPreparing your projector Indicator area Control panel Terminal panelOverview Attaching the lens capUsing the picture quality adjusting buttons Remote controlAdjustment feet Bottom sideReception angle Using the remote controlOperational range of the remote control Setting up the screen Setting up your projectorWhen the aspect ratio of the screen is Screen size and projection distanceWhen the aspect ratio of the image is Setting up your projectorWhen the aspect ratio of the screen is 2.351 CinemaScope When ﬁne streaks are seen on projected images Adjusting the position of the projected imageWhen projected images are distorted to a trapezoid Correcting skewed or distorted imageTrigger terminal Front projection, ceiling mountingRear projection Viewing video images Connecting the projector to video equipment Basic home theater system connection PreparationConnecting to a DVD player or Hdtv decoder Connecting to a video player, etcWhen a TV tuner or VCR is connected Viewing video imagesConnection for video equipment having an Hdmi terminal Connecting to video equipment having a Hdmi terminalPlugging in the power cord Projecting images To stop projecting ZOOM1 ZOOM2 Stretch ANAMORPHIC1 ANAMORPHIC2 Setting the aspect ratioWith the Feature menu See page 26 for menu setting How to change the settingsWith the remote control Plugging the power cord Connecting the projector to a computerViewing computer images About DDCComputer Viewing computer imagesSetting of the resolution When connecting to a notebook computerExample of the setting procedure for external output Auto Position buttonMenu operation Available settings in the menus How to set the menusMenu operation Image menuInstallation menu Feature menu User menu Signal menuTo enable the stored image quality settings To store the settingsAV memory Information menuTo adjust the brightness Contrast and Brightness Adjusting projected imagesTo adjust the color Color and Tint To sharpen or soften the projected image SharpnessTo adjust the tone of white Color Temp Adjusting projected imagesAbout color temperature To enable the stored color temperatureNoise reduction To adjust the ratio of change in brightness Gamma ModeLPF Progressive ﬁlter To adjust the vertical positionPassword function Advanced featuresTo enable the password function To cancel the password functionReplacing the lamp Interval of lamp replacementTo replace the lamp Reset of the lamp operation timeReplacing the lamp When removing the lamp from the ceiling-mounted projector Cleaning of the air-ﬁlter MaintenanceCleaning of the projector and the ventilation slots Cleaning of the lensNo image appears on the screen Problem Solution TroubleshootingImages are not displayed correctly Problem Solution TroubleshootingOthers Problem Solution Condition Possible Solution IndicatorsNormal condition Abnormal conditionSpeciﬁcations Dimension drawings unit mmSpeciﬁcations Replacement part option/not included in the box ConnectorsComputer IN/COMPONENT Video Hdmi VLT-HC7000LPMitsubishi Electric Corporation