CONTROLS AND FEATURES
FRONT VIEW
REAR VIEW
<Front Panel>
1
CHROMA | CONTRAST | VOLUME/SELECT | MENU |
15 |
|
|
|
PHASE | BRIGHT |
|
|
|
| 2 | 3 | 4 |
1 | Tally lamp |
|
|
|
| Lights when the tally control signal is ON. The tally control |
|
| |
| signal is input through the REMOTE (external control) |
|
| |
| remote terminal. For details, refer to Page 17. |
|
| |
2 | Chroma/Phase button |
|
| |
| [ CHROMA/ | PHASE] |
|
|
| Press this button to activate the picture color density |
|
| |
| UNDER | COLOR | BLUE | ASPECT |
| A | B | C SLOT | D | POWER |
| SCAN | OFF | CHECK |
|
| |||||
|
|
|
|
|
|
| INPUT SELECT |
|
|
|
5 | 6 | 7 | 8 | 9 | 10 | 11 |
| 12 |
| 1314 |
8 Blue Check button [BLUE CHECK]
Cuts red and green signal components. Only blue signal components are shown. Press the button again to
restore the normal image.
When selected, this button lights.
9 Aspect button [ASPECT] |
Press this button to change the aspect ratio from 4:3 to |
<Rear Panel>
18
19
20 
21 
22 
VIDEO A
INOUT
VIDEO B
INOUT
INY/C
OUT
AUDIO A
INOUT
AUDIO B
INOUT
16
SLOT
REMOTE
17
VIDEO A
VIDEO B
Y/C
AUDIO A
AUDIO B
No.51923
adjustment mode or picture hue adjustment mode. Each |
|
time you press the button, the adjustment item changes. |
|
Picture color density f Picture hue |
|
Adjust the value with the VOLUME/SELECT buttons | 4. |
Also used as a control button in the menu function mode.
3 | Contrast/Brightness button |
| ||
| [CONTRAST | / BRIGHT | ] |
|
| Press this button to activate the picture contrast adjustment |
| ||
| mode or picture brightness adjustment mode. Each time |
| ||
| you press the button, the adjustment item changes. |
| ||
| Picture contrast f Picture brightness |
| ||
| Adjust the value with the VOLUME/SELECT buttons | 4. | ||
| Also used as a control button in the menu function mode. |
| ||
4 | Volume/Select buttons | +] |
| |
| [VOLUME/SELECT | – |
| |
Adjusts the speaker volume. Also used as a control button in the menu function mode.
5 Menu button [MENU]
Displays and disappears the <MENU> screen.
Pressing the CHROMA/PHASE button2 with the Menu button depressed will display the
screen.
6 Under Scan button [UNDER SCAN]
Reduces the screen size to display the entire image.
Press the button again to cancel Under Scan.
When selected, the Under Scan button lights.
7 Color Off button [COLOR OFF]
Cuts color signals to display a black and white image.
Press the button again to restore the original color.
When selected, the COLOR OFF button lights.
Note:
●This function is invalid with RGB input.
| 16:9. |
|
|
10 | Input A (VIDEO) button [INPUT SELECT A] | ||
| Selects the video and audio signals input to the VIDEO A | ||
| * and AUDIO A | q terminals on the rear panel. The | |
| button lights when selected. |
| |
11 | Input B (VIDEO Y/C) button [INPUT SELECT B] | ||
| Selects the video and audio signals input to the VIDEO B | ||
| ( or VIDEO B (Y/C) ) and AUDIO B | w terminals on | |
the rear panel. The button lights when selected.
Note:
●The VIDEO B terminals include a video terminal (BNC connector) and a Y/C terminal
12 Input C/D (Slot) buttons [INPUT SELECT C/D (SLOT)]
Selects the signals to be input via the input cards installed in the rear panel card slots.
C, D : Selects the image from the input card in the slot. For details on input connectors and using the INPUT SELECT button, refer to page 7.
13 | Power indicator | |
| Unlit | : The main power is OFF. |
| Orange : The main power is ON, but the monitor’s power | |
|
| is OFF (in the |
| Green | : The main power is ON, and the monitor’s power |
|
| is ON (in the normal operation mode). |
14 | Power switch [POWER |
| ] |
|
Press the power switch to turn the monitor’s power ON or
OFF when the main power is ON.
Note:
●When RUSH DELAY is set to SLOW, it takes about
three seconds before power is actually supplied after the power switch is pressed.
15 Speaker
A
16 Input card slot (SLOT)
Optional input cards can be installed in this slot. Input cards are not provided when you purchase this monitor.
17 REMOTE (external control) terminal
Connect this terminal to an external control unit to enable remote operation of the monitor.
Refer to the HOW TO USE EXTERNAL CONTROL on page 17 for more details.
18 Video A terminals [VIDEO A IN/OUT]
Video signal input (IN) and output (OUT) terminals. The output terminal is
IN : Video signal input terminal
OUT :
Notes:
* For corresponding audio signals, use the AUDIO A terminals q.
*Also refer to BASIC CONNECTION EXAMPLE on page 15.
19 Video B terminals [VIDEO B IN/OUT]
Video signal input (IN) and output (OUT) terminals. The output terminal is
IN : Video signal input terminal
OUT :
Notes:
*For corresponding audio signals, use the AUDIO B terminals w.
*Also refer to BASIC CONNECTION EXAMPLE on
page 15.
20 Video B (Y/C) terminals [VIDEO B Y/C IN/OUT]
Y/C
IN :
OUT :
Notes: |
| ENGLISH |
* For corresponding audio signals, use the AUDIO B | ||
terminals | w. |
|
* When both VIDEO B terminals are connected (input) at |
| |
| ||
the same time, the Y/C terminal has priority. |
| |
* Also refer to BASIC CONNECTION EXAMPLE |
| |
on page 16.
21 Audio A terminals [AUDIO A IN/OUT]
Input (IN) and output (OUT) terminals for the audio signal
corresponding to the VIDEO A terminals | *. | |
The output terminal is |
| |
IN | : Audio signal input terminal |
|
OUT : | ||
Notes:
*For corresponding video signals, use the VIDEO A terminal *.
*Also refer to BASIC CONNECTION EXAMPLE
on pages 15 and 16.
22 Audio B terminals [AUDIO B IN/OUT]
Input (IN) and output (OUT) terminals for the audio
signals corresponding to the VIDEO B terminals | ( or | ||
VIDEO B (Y/C) terminals | ). |
| |
The output terminal is |
| ||
IN | : Audio signal input terminal |
| |
OUT : | |||
Notes: |
|
| |
* For corresponding video signals, use the VIDEO B |
| ||
terminals (or VIDEO B (Y/C) terminals | ). | ||
*Also refer to BASIC CONNECTION EXAMPLE on pages 15 and 16.
TM-
4
5
H1750CG