JVC TM-H1750CG Preparation, HOW to Handle Basic Operations,  Installing the Input Card

PREPARATION

 INSTALLING THE INPUT CARD

1. Turn off the Color Video Monitor	’s main power and unplug the power cable
from the AC outlet.

HOW TO HANDLE BASIC OPERATIONS

BASIC OPERATION

STATUS indication

1. Press the main power switch to turn on the power.(PAL or NTSC)

2. Press the POWER switch to turn on the power.

PAL

2.Unscrew the screws and remove the slot cover from the slot (on the rear side of the monitor) in which you are going to install the card.

Rear side of the TM-H1750CG

color video monitor

SLOT

REMOTE

ON	:	Power turns ON. (Power indicator: lit)
POWER		Green	: The main power is ON, and the monitor’s
OFF	:		power is ON (in the normal operation mode).
		Power turns OFF. (Power indicator: unlit)
		Orange : The main power is ON, but the monitor’s
			power is OFF (in the standby mode)
		Unlit	: The main power is OFF.

3. Press the INPUT SELECT buttons to choose input.

Select video/audio signals input to terminals on the rear panel. The selected button lights in green.

About the STATUS indication

● With the COLOR SYSTEM setting set

to AUTO mode, when you turn on the

	Slot cover
	VIDEO A
	VIDEO B
	Y/C
No.	3. Insert the Input Card ’s board (green-colored) into the slot, fitting the board into
51923	the guide rails on the top and bottom of the slot.

A B C SLOT D

INPUT SELECT

INPUT	Terminals on the rear panel
SELECT
buttons	Video signal input		Audio signal input
1 Input A	VIDEO A terminal	AUDIO	A terminal
(VIDEO)
2 Input B	VIDEO B terminal			AUDIO B terminal
(VIDEO/Y/C)
	VIDEO B (Y/C) terminal
3 Input C	Refer to page 7 for details about the input terminals
4 Input D	on each card and the INPUT SELECT button.

Note: The Y/C (S-video) terminal has priority.

power or select inputs, the color

system indication appears for about

3 seconds on the screen while PAL or

NTSC signals are being detected.

It does not appear when receiving a

B/W signal or when no signal is input.

Refer to page 11 for more information

about COLOR SYSTEM setting and

page 12 for more information about

STATUS indication setting.

ENGLISH

	Fit the board to
	the guide rails.
Knob		SLOT
	REMOTE
	VIDEO A	Guide rails
	VIDEO B
		Y/C
	Input card (the illustration
Knob	shown is of the IF-C01COMG)
4. Push the Input Card in so that its front panel touches the monitor			’s rear panel.

5. Secure the Input Card by replacing the screws removed in Procedure 2.

SLOT

REMOTE

VIDEO A

VIDEO B

Y/C

NOTE : Do not touch the terminal connected to the monitor or board pattern.

Do not remove slot covers from the monitor’s slots if they are not in use.

8

1-5

4.Press the VOLUME/SELECT buttons to adjust the speaker volume.

Press this button to display the speaker volume level on the

VOLUME/SELECT	screen.
	+ : The Built-in speaker volume is increased. (00	= 50)
	– :The Built-in speaker volume is decreased. (50	= 00)

*Screen indication will disappear about 10 seconds after operating.

*The on-screen display goes off when you press MENU button.

PICTURE ADJUSTMENT

1. Press select buttons corresponding to the item you want to adjust.

CHROMA	CONTRAST	The item you select is displayed on the screen.
		1 Chorma control	: Press the CHROMA/PHASE button once.
		2 Phase control	: Press the CHROMA/PHASE button twice.
PHASE	BRIGHT	3 Contrast control	: Press the CONTRAST/BRIGHT button once.
		4 Brightness control : Press the CONTRAST/BRIGHT button twice.

* Pressing the CHROMA/PHASE button and CONTRAST/BRIGHT button alternately while the item is shown on screen restores the previous status. When no item is shown on screen, CHROMA and CONTRAST have priority.

2. Adjust with the VOLUME/SELECT buttons.

	Items	VOLUME/SELECT button
VOLUME/SELECT		–	+
	CHROMA	lighter	deeper
	(Chroma)
	PHASE	reddish	greenish
	(Phase)
	CONTRAST	lower	higher
	(Contrast)
	BRIGHT	darker	brighter
	(Brightness)

*Screen indication will disappear about 10 seconds after operating.

*The on-screen display goes off when you press MENU button.

			00 ~ 50
VOLUME	:	20
		–	+
			UPPER
			–40 ~ +40
PHASE	:	00
PHASE	:	00
		–	+

Notes:LOWER

●Phase control is effective only in the NTSC color system mode.

●Chroma control is not effective when receiving RGB and B/W or when no signal is input. (Except when a component signal is input.)

●When CHROMA is adjusted to “–40,” the picture becomes less colorful.

●“NO EFFECT” is displayed (for about 3 seconds) when your selected function has no effect.

●To change the display position on screen, set UPPER or LOWER with

ADJ. BAR POSI.

9

TM-H1750CG