HOW TO INITIALIZE THE SETTING
SCREEN DISPLAY AND SELECTIONS IN THE <SET-UP MENU> RESET MODE
BASIC CONNECTION EXAMPLE
Notes:
•Before connecting your system, make sure that all units are turned off. |
| |
•The illustration below shows some examples of diff | erent connections. Terminal connections may differ depending on the component connected. |
|
Be sure to refer to the instructions provided with the unit(s) you are connecting. |
| |
•Each pair of input (IN) and output (OUT) terminals are |
| |
•If you’re not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the brid | ged output (OUT) | |
terminal as this will cause the terminating resistance switch to open (auto terminate function). |
| |
•When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components | . | |
You can set <MENU> and
1.Press the Power ( 
) switch to turn the power OFF (activate the standby mode).
POWER
<SET–UP MENU> RESET
Are you sure ? “Yes” then <+> “No” then <MENU>
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by th | e same video |
signal “looping” between the VCRs, and is not a malfunction.) |
|
•Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When | both |
VIDEO B terminals are connected (input) at the same time, the Y/C terminal has priority.
VIDEO A Connection Example (Select Input A (VIDEO))
2. While pressing both MENU button and | CHROMA/ | |||||
PHASE button, press the Power ( |
|
| ) switch to turn | |||
| ||||||
the power ON. |
|
|
|
| ||
|
|
| The | |||
CHROMA | MENU | POWER | * The screen automatically disappears when no operation | |||
|
|
| is performed after about 5 minutes. |
| ||
PHASE |
|
| Note: |
| ||
● The |
Initial settings
Sorts | Functions (Items) | Initialization | ||
(setting) | ||||
|
| |||
| APERTURE | 00 |
| |
| ADJ. BAR POSI | LOWER | ||
screen | COLOR TEMP | 6500 |
| |
COLOR SYSTEM |
| AUTO | ||
<MENU> | COMPO. LEVEL | 00 |
| |
RUSH DELAY | STD |
| ||
|
| |||
| PICTURE SUB ADJ. |
|
| |
Video Camera |
Video Monitor |
VIDEO A
Video
(Video signal cable)
IN
VIDEO B
IN
Audio
(Audio signal cable) | IN |
|
OUT
Video
(Video signal cable)
OUT
Video
(Video signal cable)
OUT
Y/C
ENGLISH
No
displayed if the MENU or CHROMA/PHASE buttons are |
pressed for a very short time. Keep pressing them until |
the display screen appears. |
CONTRAST | 00 |
BRIGHT | 00 |
CHROMA | 00 |
VCR |
AUDIO A
IN
OUT
Audio
(Audio signal cable)
.51923
3.Setting
Initialization is required.
| PHASE | 00 |
| H. POSITION | 00 |
| V. POSITION | 00 |
| WHITE BALANCE |
|
screen | R. CUT OFF | 00 |
G. CUT OFF | 00 |
| AUDIO B |
VIDEO B (VIDEO) Connection | IN |
Example (Select Input B (VIDEO)) |
|
Audio
(Audio signal
OUT cable)
B. CUT OFF 00 |
VOLUME/SELECT
Press the VOLUME/SELECT [+] button.
*Initialization is completed, and the
MENU> | R. DRIVE | 00 | ||
B. DRIVE | 00 | |||
| CONTROL LOCK | OFF | ||
| STATUS DISPLAY | ON |
| |
| REMOTE SYSTEM | MAKE |
| |
Initialization is not required.
INPUT REMOTE | A – D |
MENU
Press the MENU button.
* Initialization is aborted, and the
adjustment | CHROMA | 00 | |
PHASE | 00 | ||
CONTRAST | 00 | ||
BRIGHT | 00 | ||
Picture | |||
|
| ||
|
|
| |
Volume | VOLUME | 20 | |
|
|
Video Camera |
Video Monitor |
VCR |
Video
(Video signal cable)
Audio
(Audio signal cable)
: Signal Flow
VCR |
Video Monitor |
14 | 15 |