JVC DT-V9L1D Setting of sub menu Posi, Color of the format indicator, Picture SUB ADJ

Page 12

Menu Configuration—SET-UP MENU

For the operation procedure, see page 7.

Operation guide Shows the buttons for each operation.

The menu automatically disappears in about 30 seconds after the previous operation.

Some items may not appear on the menu depending on the input or the input signal.

• The items controlled by the MAKE system do not appear on the menu.

NOTE

Setting of “sub menu POSI.”

The setting values and features are as follows.

LOWER1: Displays the current setting and adjustment bar at the lower part of the screen.

UPPER1: Displays the current setting and adjustment bar at the upper part of the screen.

LOWER2: Displays the current setting at the lower part of the screen.

UPPER2: Displays the current setting at the upper part of the screen.

• The adjustment bar is not displayed for some items.

Color of the format indicator

When “FORMAT INDICATOR” is set to “ON,” the tally lamp lights as follows according to the incoming video signal.

Lights in green: 720/60p, 720/59.94p, 720/50p, 1080/60i, 1080/59.94i, 1080/50i, 1035/60i, 1035/59.94i, 1080/24psF, 1080/23.97psF, 1080/30psF, 1080/25psF, 1080/29.97psF

Lights in red: 480/59.94i, 576/50i, 480/59.94p, 576/50p

Lights in orange: composite signal

 

 

 

12

FUNCTION SETTING

 

 

 

Setting for the sub menu display, color system, color of the tally lamp, and format indicator

 

Item

To do

Setting value

sub menu POSI.

Select the contents and displaying position of “sub menu.”

“NOTE”

COLOR SYSTEM

Select the color system.

AUTO, NTSC, PAL

 

 

• If the picture is unstable with “AUTO,” select “NTSC” or “PAL.”

 

TALLY SELECT

Select the color of the tally lamp.

GREEN, RED

FORMAT INDICATOR

Select whether to use the tally lamp as the format indicator.

OFF, ON (“NOTE”)

When “FORMAT INDICATOR” is set to “ON,” the TALLY function of the MAKE/TRIGGER terminal is not available.

PICTURE SUB ADJ.

Adjusts the standard level for the picture adjustment and selects the set-up level for the input video signal.

Item

To do

Setting value

CONTRAST*1

Adjust the standard level for the contrast adjusted with

–20 – +20

 

CONTRAST knob on the front panel.

 

BRIGHT*1

Adjust the standard level for the brightness adjusted

–20 – +20

 

with BRIGHT knob on the front panel.

 

CHROMA*1

Adjust the standard level for the chroma adjusted with

–20 – +20

 

CHROMA knob on the front panel.

 

PHASE

Adjust the standard level for the phase adjusted with

–20 – +20

 

PHASE knob on the front panel.

 

NTSC SETUP

Select the set-up level of the input NTSC signal.

00 (compliant with 0% set-up signal), 7.5

 

 

(compliant with 7.5% set-up signal)

COMPO. LEVEL

Select the level of the analog component signal (480i

SMPTE (compliant with M2VTR signals),

 

and 576i only).

B75 (compliant with BetacamVTR 7.5%

 

 

set-up signal), B00 (compliant with

 

 

BetacamVTR 0% set-up signal)

sub menu

Display the sub menu which enables you to adjust the items in “PICTURE SUB ADJ.” while viewing

 

the actual picture.

 

reset

Restore the default settings for all the items in “PICTURE SUB ADJ.”

• When the DYNAMIC lamp lights, “PICTURE SUB ADJ.” does not appear on the menu (t on page 6).

H. POSITION*2 Setting value: –003 – +003

Adjusts the horizontal picture position.

WHITE BALANCE SET.

Selects the color temperature and adjusts the drive level of each color (R/G/B).

Item

To do

Setting value

COLOR TEMP.

Select the color temperature.

6500K, USER, 9300K

R DRIVE, G DRIVE,

Adjust the drive level of each color (red, green, and blue).

–128 – 000 – MAX

B DRIVE*3

 

 

sub menu

Display the sub menu which enables you to adjust the items in “WHITE BALANCE SET.” while

 

viewing the actual picture.

 

reset

Restore the default settings for the drive levels of the selected color temperature.

When “COLOR RANGE MODE” is set to “ON,” “WHITE BALANCE SET.” does not appear on the menu (page 10).

*1 Memorized for each input — composite signal input (VIDEO), component signal input (COMPO.), and SDI signal input. *2 Memorized for each signal format.

*3 Memorized for each color temperature.

• The lamp goes off when the non-compliant video signals are coming in.

Image 12
Contents DT-V9L1D Safety Precautions How to replace the fuseRating label is on the bottom of the monitor These openings must not be blocked or coveredMaintenance Installation To adjust the stand heightHigher position Align as illustratedFix the monitor to a wall by using strings Lower positionTo prevent an accidental fall Fixing the monitorFront panel Press or button when a menu is not displayed Display the menuPress buttons to select an item, then press button Press buttons to select an audio channelRear panel Available signals To detach the cover, release the tab. TabMenu Configuration-MAIN Menu Setting of Marker Select and R-MARKER SelectPicture Improvement Area MARKER*1Setting of E.AUDIO Group Audio SettingSync Function Setting of sub menu Posi Color of the format indicatorPicture SUB ADJ White Balance SETSetting of Character SET Setting for the information display of the monitorSetting value OFF, on InformationUsing the MAKE/TRIGGER system External ControlAbout the external control Using the RS-232C system Command outlineBasic command list Specifications of the RS-232C terminalTroubleshooting Self-check programFollowing are not malfunctions FlashingSpecifications GeneralInput/output terminals Dimensions Unit mm Front viewSide view Rear view