JVC DT-V9L1D specifications Maintenance

Page 3

U.S.A. only

FCC NOTICE

CAUTION: Changes or modifications not approved by JVC could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

IMPORTANT RECYCLING INFORMATION

This product has a fluorescent lamp that contains mercury. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities or for USA, the Electronic Industries Alliance: http://www.eiae.org

European Union only

Dear Customer,

This apparatus is in conformance with the valid European directives and standards regarding electromagnetic compatibility and electrical safety.

European Union only

EMC Supplement

This equipment is in conformity with the provisions and protection requirements of the corresponding European Directives. This equipment is designed for professional video appliances and can be used in the following environments:

Controlled EMC environment (for example purpose built broadcasting or recording studio), and rural outdoors environment (far away from railways, transmitters, overhead power lines, etc.)

In order to keep the best performance and ensure electromagnetic compatibility, we recommend to use cables not exceeding the following length:

Cable

 

Length

Power cord

(attached cable (H05VV-F 3 x 0.75 mm2))

2.0 m

Video signal cable

(coaxial cable)

2.0 m

Audio signal cable

(shielded cable)

1.5 m

RS-232C cable

(shielded cable)

2.0 m

(A straight cable with a D-sub 9-pin connector)

 

REMOTE cable

(twist pair cable)

2.0 m

(A straight LAN cable)

 

 

The inrush current of this apparatus is 6.269 ampere.

CAUTION

In case where the strong electromagnetic waves or magnetism are near the audio cable or the signal cable, the sound or the picture will contain noise. In such cases, please keep the cable away from the sources of the disturbance.

European representative of Victor Company of Japan, Limited is: JVC Technology Centre Europe GmbH

Postfach 10 05 52

61145 Friedberg Germany

Information for Users on Disposal of Old Equipment

[European Union]

This symbol indicates that the electrical and electronic equipment should not be disposed as general household waste at its end-of-life. Instead, the product should be handed over to the applicable collection point for the recycling of electrical and electronic equipment for proper treatment, recovery and recycling in accordance with your national legislation.

 

 

 

By disposing of this product correctly, you will help to conserve natural resources and will

 

 

 

help prevent potential negative effects on the environment and human health which could

 

 

 

otherwise be caused by inappropriate waste handling of this product. For more information

 

 

 

about collection point and recycling of this product, please contact your local municipal

Attention:

office, your household waste disposal service or the shop where you purchased the

This symbol is

product.

only valid in the

 

European Union.

Penalties may be applicable for incorrect disposal of this waste, in accordance with

 

 

 

national legislation.

 

 

 

(Business users)

 

 

 

If you wish to dispose of this product, please visit our web page www.jvc-europe.com to

 

 

 

obtain information about the take-back of the product.

 

 

 

[Other Countries outside the European Union]

 

 

 

If you wish to dispose of this product, please do so in accordance with applicable national

 

 

 

legislation or other rules in your country for the treatment of old electrical and electronic

Maintenance

Unplug this product from the wall outlet before cleaning.

Screen

To avoid irreparable change in appearance of the screen such as uneven color, discoloration, scratches, be careful about the following:

Do not paste or stick anything using any glues or adhesive tapes.

Do not write anything on the screen.

Do not strike the screen with a hard object.

Avoid condensation on the screen.

Do not wipe the screen with solvent such as alcohol, thinner, or benzine.

Do not wipe the screen forcefully.

If the screen gets stained, wipe it with a soft dry cloth, a soft damp cloth, or a soft cloth soaked in water- diluted neutral detergent and wrung well.

Cabinet

To avoid the deterioration or damages of the cabinet such as its paint’s peeling away, be careful about the following:

Do not wipe the cabinet using solvent such as alcohol, thinner, or benzine.

Do not expose the cabinet to any volatile substance such as insecticides.

Do not allow any rubber or plastic in contact for a long time.

Do not wipe the cabinet forcefully.

Wipe stains off the cabinet with a soft cloth. If the cabinet gets heavily stained, wipe it with a soft cloth soaked in water-diluted neutral detergent and wrung well, then wipe with a soft dry cloth.

Ventilation openings

Use a vacuum cleaner to get rid of the dust around the intakes (all the openings). If a vacuum cleaner is not available, use a cloth and wipe it off. Leaving the dust around the intakes may prevent proper temperature control and cause damage to the product.

equipment.

ENGLISH3

Image 3
Contents DT-V9L1D These openings must not be blocked or covered Safety PrecautionsHow to replace the fuse Rating label is on the bottom of the monitorMaintenance Align as illustrated InstallationTo adjust the stand height Higher positionFixing the monitor Fix the monitor to a wall by using stringsLower position To prevent an accidental fallFront panel Press buttons to select an audio channel Press or button when a menu is not displayedDisplay the menu Press buttons to select an item, then press buttonRear panel To detach the cover, release the tab. Tab Available signalsArea MARKER*1 Menu Configuration-MAIN MenuSetting of Marker Select and R-MARKER Select Picture ImprovementSetting of E.AUDIO Group Audio SettingSync Function White Balance SET Setting of sub menu PosiColor of the format indicator Picture SUB ADJInformation Setting of Character SETSetting for the information display of the monitor Setting value OFF, onUsing the MAKE/TRIGGER system External ControlAbout the external control Specifications of the RS-232C terminal Using the RS-232C systemCommand outline Basic command listFlashing TroubleshootingSelf-check program Following are not malfunctionsSpecifications GeneralInput/output terminals Rear view Dimensions Unit mmFront view Side view