JVC G2000 manual Control Panel

Page 11

Controls and Features (cont.)

Control Panel

STAND BY

1

 

2

 

3

LAMP

4

TEMP

5

EMERGENCY

6

VIDEO

7

COMPUTER

8

SETTING

9

+3

 

QUICK

p

ALIGN

-2

 

1STAND BY Indicator

ON : When in stand-by mode.

Blinking : When in cool-down mode.

4Lamp indicator

ON

: After the light-source lamp has been used for

 

more than approx. 900 hours.

Blinking : Replace the lamp. Refer to “Replacing the Light- Source Lamp” on page 61.

5TEMP indicator

ON: The temperature inside the projector has abnormally risen.

Note

•While the TEMP indicator is on (during abnormal temperature), the power is automatically cut off, and an emergency mode is shown (with the EMERGENCY indicator blinking).

6EMERGENCY indicator

Blinking: Something abnormal has occurred with the projector.

Memo

About the emergency mode:

The emergency mode is shown when the following anomalies have occurred with the projector (the EMERGENCY indicator blinks). In the emergency mode, projection is automatically interrupted and the cooling fans operate for about 20 seconds.

•When the air filter is displaced.

•When the filter is clogged.

•When the light-source lamp has suddenly gone off.

•When the fans have stopped.

•When the temperature inside has risen abnormally high.

Memo

About the cool-down mode:

This projector has a function to cool down the heated lamp for a fixed period of time (approx. 120 seconds) after projection is finished. This feature is referred to as the cool-down mode.

CAUTION

•The purpose of the cool-down mode is to prevent inner parts from being deformed or broken by heat from the heated lamp as well as to prolong the life of the lamp. Do not turn off the main power switch while in the cool-down mode. Also, do not place the projector on its side or stand it upright; this may block the exhaust vents.

2OPERATE indicator

ON: When the projector is in operation (projecting)

3OPERATE button

When the projector is in the stand-by mode, press this button one second or more, and the main power switch is turned on, causing the OPERATE indicator to light. Press it one second or more again, and the projector goes into the cool-down mode, then stand-by mode.

Memo

While in the cool-down mode:

If you press the OPERATE button, the projector is not tuned on.

CAUTION

• When an emergency mode is shown:

After the cooling fans have stopped, turn off the main power switch and unplug the power cord from the wall outlet. Make sure the lamp-replacement cover and the air filter are correctly installed. Then, plug in the power cord again and operate the projector.

If it goes into an emergency mode again, after the cooling fans have stopped, turn off the main power switch, unplug the power cord, and call your dealer for repair.

ENGLISH

9

G2000 p.05-14

9

99.11.20, 3:28 AM

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Model No No de modèle G2000 Serial No No de série For customer UsePour l’utilisateur G2000 CoverA4 99.11.19, 1042 PM G2000 About burning-in of the D-ILA device Safety PrecautionsXenon gas is enclosed with high pressure inside the light Safety PrecautionsLighters that present special hazards when over heated Lamp is turned on. Exposure of your eyes to the strongContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesControl panel Connector panelHow to extend the adjustable foot on the rear Left-hand sideFixing foot Position selecting screw for ceiling mounting Bottom SurfaceAir intake area filter Opening for replacing the light-source lampControl Panel Computer button Setting buttonWhen a menu is shown Video buttonComputer OUT computer output terminal D-sub 3-row 15 pin Connector PanelC S video input terminal Mini DIN 4 pin RS-232C terminal D-sub 9 pinAudio audio input terminal stereo mini jack Input of external sync signals is automatically detectedAudio input terminal stereo mini jack Row 15 pinRemote Control Unit Open the back cover Installing BatteriesInstall the batteries Precautions for using batteriesWhen installing the projector, observe the followings Installing the ProjectorPrecautions for Installation Do not install the projector in the following placesProjection Projection Distance and Screen SizeProjection screen size diagonal length Center line of the lens65.6 ft 20.0 m 345 Approx cm 521 55.76 ft 17.0 m 294 Approx cm 44359.04 ft 18.0 m 311 Approx cm 469 62.32 ft 19.0 m 328 Approx cm 495Effective range and distance of the remote control unit Effective Range and Distance of the Remote Control UnitSetting the position selecting screw for Ceiling Mounting Computer signals Connecting to Various DevicesSignals that Can Be Input to the Projector Video signalsHi-Vision devices Connecting to Video DevicesConnecting to Hi-Vision Devices Video devicesGame device, etc Connecting to Other DevicesConnecting to Devices which Control the Projector Desktop typeRGB output devices Connecting to Computer DevicesConnection to an IBM PC or IBM-compatible computer Read the manual which comes with each device thoroughlyPersonal computer connection cable To monitor connector SuppliedConnection to Macintosh To prevent fire and electric shock, observe the following Connecting the Power Cord SuppliedTo use the projector Remove the lens capWhen Turning On the Devices Connected to the Projector Press the Operate button for one second or more Turning on the PowerTurn on the Main Power switch Basic OperationsWhen you press Computer Adjust the screen sizeSwitch the input When you press VideoButtons Adjust focusAdjust sound volume Adjust focus with the remote control’s Focus +Press once To turn off video image and audio sound temporarilyTo use the quick alignment function Projector’s buttonProjector button To display the Setting menuTo use the remote control’s Preset button Values, press the remote control’s Preset buttonBack button To display ChannelPress the Setting button to select the desired item Operating the Setting MenuMaking Basic Settings Press the Setting button of the projectorOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu To finish the main menu, press the page Back button Changing the Color SystemSelect Decoder with the cursor button 5 or Set the color system with the cursor button 2 orButton Changing the Language DisplaySelect Language with the cursor button 5 or Set the desired language with the cursor button 2 orMain menu appears on the screen Adjusting the Pixel ClockAdjust Tracking and Phase with the cursor buttons Select Pixel Clock with the cursor button 5 orSelect Position with the cursor button 5 or Adjusting the Screen PositionAdjust H. POS. and V. POS. with the cursor buttons When computer-related signals are input Adjusting Picture QualitySelect the item to adjust with the cursor button 5 or When AV signals are inputPicture menu Submenu itemsFor video system input For computer system input30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddish Sets a mode which allows easyAdjustment values 0, text 30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lowerButton 5 or Adjusting Sound QualityAdjust Treble and Bass with the cursor buttons Select the Sound with the cursorSelect the Options with the cursor button 5 or Setting and Adjusting Other Functions OptionsSelect the item to set adjust with the cursor button 5 or Following optional functions can be set adjustedOptions menu Set adjust the desired item with the cursor button 2 orAspect Source item displayed in text is indicated in magenta color Changing Setting the SourceSelect a submenu item Source using the cursor button 5 or Select the item to set using the cursor buttons 5/ or 2/3Fix it When Auto is selectedWhen a dedicated source mode is selected When User is selectedSubmenu item Channel Setting Up ChannelsChannel Setup menu Select the Channel with the cursor button 5 orPress the MENU/ENTER button to set fix To delete the contents of the channel registered set upFix Press the cursor button 5or to select a Line itemSOURCE’ or SWNo item. First register a Line item Channel setup menuSource Setup menu is displayed on the screen If any Line item is not registered, you cannot choose aPress the MENU/ENTER button to set Press the page Back button To set up a switcher number SWNoPress the cursor button 3 to move to SWNo Press the cursor button 2or 3to select a numberSelect the Channel number with the cursor button 5 or Press the page Back when no menu is displayedTo changing channels using a Direct Channel Changing ChannelsSubmenu item Channel Source Channel Setup/Selection menuSelected CH is shown in magenta color Submenu item User Source Setup Setting up or Change User SourcesPress the cursor button 5 or to select User Source Setup Before setting up a user sourcePress the cousor button 3 to move to User Name Up to 9 input positions can be selected User Name Setup menuTo delete user names Overwrite the user name with spacesPress the cursor button 5or to select Display Size Setting up or Changing the Display SizePress the cursor button 5or to select an item to adjust Press the cursor button 2or 3to make adjustmentsFuse 15A Fuse holder Place the main power switch to the OFF à positionReplacing the Fuse Loosenit. the fuse holder to removeLoosen the two screws with a flat-end screwdriver Remove the lamp-replacementReplacing the Light-Source Lamp Opening cover by Loosening ScrewsFasten the two screws with a flat-end screwdriver Insert the new lamp unit fully inside and fasten the screwsProjector’s button Resetting the Lamp Use TimeTurn on the Main Power switch to go into stand-by mode This completes the resetting of the lamp use timeFasten the screw with a flat-end screwdriver Cleaning and Replacing the FilterClean the filter Reinstall the filterTroubleshooting Maintenance When the emergency indicator starts blinkingComputer in Computer input SpecificationsAV in AV in input Other Front Outside dimensionsDTV-format signals TopComputer IN-1 PC / Computer OUT Terminal Pin assignment Specifications for terminalsTerminal RS-232C terminalG2000 CoverA4 99.11.19, 1042 PM Hughes-JVC Technology Corporation
Top Page Image Contents