JVC G2000 manual Resetting the Lamp Use Time, Projector’s button

Page 65

Replacing the Light-source Lamp (Cont.)

Resetting the Lamp Use Time

After replacing with a new light-source lamp, reset the counter inside the projector. This works to reset the life calculation of the light-source lamp, allowing the used time of the new light-source lamp to be accumulated.

■Projector’s button

[MAIN POWER switch]

1

1 Turn on the MAIN POWER switch to go into stand-by mode.

•ON [ ❙ ]:The main power turns ON and the STAND BY indicator lights.

2 Press and hold down the “VIDEO”, “SETTING” and “QUICK ALIGN. +

3” at the same time for six seconds or more.

•The STAND BY and OPERATE indicators come on at the same time.

[Control panel]

STAND BY

LAMP

TEMP

EMERGENCY

VIDEO

COMPUTER

SETTING

+3

QUICK

ALIGN

-2

STAND BY indicator

OPERATE indicator

2

3

3 While the STAND BY and OPERATE indicators are on, press the “VIDEO”, “SETTING”, and “COMPUTER” buttons at the same time.

•The STAND BY and OPERATE indicators blink two seconds alternately, and after blinking, the projector returns to stand-by state (the STAND BY indicator lights).

* This completes the resetting of the lamp use time.

Memo

To check the lamp use time has been reset :

You can check it by LAMP TIME on the OPTIONS menu.

CAUTIONS

•After replacing with a new light-source lamp, be sure to reset the lamp use time. When the lamp use time indicates 1000 hours, and if it is not reset, the projector does not operate. (The light-source lamp does not turn on.)

•Reset the lamp use time only when you have replaced with a new light-source lamp. Never reset it at a halfway time. Otherwise, the replacement time may become unclear, degrade performance markedly, or cause lamp explosion.

ENGLISH

63

G2000 p.60-71

63

99.11.20, 3:30 AM

Image 65

Contents Model No No de modèle G2000 Serial No No de série For customer UsePour l’utilisateur G2000 CoverA4 99.11.19, 1042 PM G2000 About burning-in of the D-ILA device Safety PrecautionsLighters that present special hazards when over heated Safety PrecautionsLamp is turned on. Exposure of your eyes to the strong Xenon gas is enclosed with high pressure inside the lightContents Accessories Front Side / Top Surface / Right Side Controls and FeaturesHow to extend the adjustable foot on the rear Connector panelLeft-hand side Control panelAir intake area filter Bottom SurfaceOpening for replacing the light-source lamp Fixing foot Position selecting screw for ceiling mountingControl Panel When a menu is shown Setting buttonVideo button Computer buttonC S video input terminal Mini DIN 4 pin Connector PanelRS-232C terminal D-sub 9 pin Computer OUT computer output terminal D-sub 3-row 15 pinAudio input terminal stereo mini jack Input of external sync signals is automatically detectedRow 15 pin Audio audio input terminal stereo mini jackRemote Control Unit Install the batteries Installing BatteriesPrecautions for using batteries Open the back coverPrecautions for Installation Installing the ProjectorDo not install the projector in the following places When installing the projector, observe the followingsProjection screen size diagonal length Projection Distance and Screen SizeCenter line of the lens Projection59.04 ft 18.0 m 311 Approx cm 469 55.76 ft 17.0 m 294 Approx cm 44362.32 ft 19.0 m 328 Approx cm 495 65.6 ft 20.0 m 345 Approx cm 521Effective range and distance of the remote control unit Effective Range and Distance of the Remote Control UnitSetting the position selecting screw for Ceiling Mounting Signals that Can Be Input to the Projector Connecting to Various DevicesVideo signals Computer signalsConnecting to Hi-Vision Devices Connecting to Video DevicesVideo devices Hi-Vision devicesConnecting to Devices which Control the Projector Connecting to Other DevicesDesktop type Game device, etcConnection to an IBM PC or IBM-compatible computer Connecting to Computer DevicesRead the manual which comes with each device thoroughly RGB output devicesPersonal computer connection cable To monitor connector SuppliedConnection to Macintosh To use the projector Connecting the Power Cord SuppliedRemove the lens cap To prevent fire and electric shock, observe the followingWhen Turning On the Devices Connected to the Projector Turn on the Main Power switch Turning on the PowerBasic Operations Press the Operate button for one second or moreSwitch the input Adjust the screen sizeWhen you press Video When you press ComputerAdjust sound volume Adjust focusAdjust focus with the remote control’s Focus + ButtonsTo use the quick alignment function To turn off video image and audio sound temporarilyProjector’s button Press onceTo use the remote control’s Preset button To display the Setting menuValues, press the remote control’s Preset button Projector buttonBack button To display ChannelMaking Basic Settings Operating the Setting MenuPress the Setting button of the projector Press the Setting button to select the desired itemOperating the Main Menu Configuration of the Main Menu Computer-related input Operating the Main Menu Basic Operation of the Main Menu Select Decoder with the cursor button 5 or Changing the Color SystemSet the color system with the cursor button 2 or To finish the main menu, press the page Back buttonSelect Language with the cursor button 5 or Changing the Language DisplaySet the desired language with the cursor button 2 or ButtonAdjust Tracking and Phase with the cursor buttons Adjusting the Pixel ClockSelect Pixel Clock with the cursor button 5 or Main menu appears on the screenSelect Position with the cursor button 5 or Adjusting the Screen PositionAdjust H. POS. and V. POS. with the cursor buttons Select the item to adjust with the cursor button 5 or Adjusting Picture QualityWhen AV signals are input When computer-related signals are inputFor video system input Submenu itemsFor computer system input Picture menuAdjustment values 0, text Sets a mode which allows easy30 ← 0 ← +30 Gets brighter 30 → 0 → +30 Gets lower 30 ← 0 ← +30 Gets higher 30 → 0 → +30 Gets less reddishAdjust Treble and Bass with the cursor buttons Adjusting Sound QualitySelect the Sound with the cursor Button 5 orSelect the item to set adjust with the cursor button 5 or Setting and Adjusting Other Functions OptionsFollowing optional functions can be set adjusted Select the Options with the cursor button 5 orOptions menu Set adjust the desired item with the cursor button 2 orAspect Select a submenu item Source using the cursor button 5 or Changing Setting the SourceSelect the item to set using the cursor buttons 5/ or 2/3 Source item displayed in text is indicated in magenta colorWhen a dedicated source mode is selected When Auto is selectedWhen User is selected Fix itChannel Setup menu Setting Up ChannelsSelect the Channel with the cursor button 5 or Submenu item ChannelFix To delete the contents of the channel registered set upPress the cursor button 5or to select a Line item Press the MENU/ENTER button to set fixSource Setup menu is displayed on the screen Channel setup menuIf any Line item is not registered, you cannot choose a SOURCE’ or SWNo item. First register a Line itemPress the MENU/ENTER button to set Press the cursor button 3 to move to SWNo To set up a switcher number SWNoPress the cursor button 2or 3to select a number Press the page Back buttonTo changing channels using a Direct Channel Press the page Back when no menu is displayedChanging Channels Select the Channel number with the cursor button 5 orSubmenu item Channel Source Channel Setup/Selection menuSelected CH is shown in magenta color Press the cursor button 5 or to select User Source Setup Setting up or Change User SourcesBefore setting up a user source Submenu item User Source SetupPress the cousor button 3 to move to User Name To delete user names User Name Setup menuOverwrite the user name with spaces Up to 9 input positions can be selectedPress the cursor button 5or to select an item to adjust Setting up or Changing the Display SizePress the cursor button 2or 3to make adjustments Press the cursor button 5or to select Display SizeReplacing the Fuse Place the main power switch to the OFF à positionLoosenit. the fuse holder to remove Fuse 15A Fuse holderReplacing the Light-Source Lamp Remove the lamp-replacementOpening cover by Loosening Screws Loosen the two screws with a flat-end screwdriverFasten the two screws with a flat-end screwdriver Insert the new lamp unit fully inside and fasten the screwsTurn on the Main Power switch to go into stand-by mode Resetting the Lamp Use TimeThis completes the resetting of the lamp use time Projector’s buttonClean the filter Cleaning and Replacing the FilterReinstall the filter Fasten the screw with a flat-end screwdriverTroubleshooting Maintenance When the emergency indicator starts blinkingComputer in Computer input SpecificationsAV in AV in input Other DTV-format signals Outside dimensionsTop FrontTerminal Pin assignment Specifications for terminalsRS-232C terminal Computer IN-1 PC / Computer OUT TerminalG2000 CoverA4 99.11.19, 1042 PM Hughes-JVC Technology Corporation